manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 178

13-65

IM 701210-06E

Saving and Loading Data

13

Explanation

Selecting the Storage Medium and Directory: File List

Media on which saving and loading are possible are displayed on the File List window.

• Display Examples of Storage Media

[FD]:

Floppy disk

[ZIP]:

Zip disk

[PC Card]:

PC card

[HD]:

Hard disk

[SCSI5]:

SCSI device with the ID number set to 5

1

[SCSI5-1]:

Partition 1 of a CSI device whose ID number is 5

1

[NetWork]:

Network drive when the Ethernet interface option is installed)

[USB]:

USB storage device

1. When a SCSI device whose ID number is 5 is connected

Selecting the File Attribute: Attr (Excluding Net Drive)

Select the file attribute of each file from the following list of choices.

• R/W

Read and write possible.

• R

Read only.  Cannot write to the file or delete the file.

Changing the Directory/File Name of the Storage Medium: Rename

Number of characters and types that can be used

Item

Number of Characters

Characters That Can Be Used

Directory name

1 to 16 characters

0 to 9, A to Z, %, _, (, ), -

File name

1 to 16 characters

0 to 9, A to Z, %, _, (, ), -

*

However, a directory name that starts with “ND” (ND000 for example) is not allowed.

Creating a Directory: Make Dir

You can create a new directory in the medium.  See above for the assignment of the

directory name when creating a new directory.

Specifying the File to Be Displayed on the File List Window: Filter

Specify the type of files to be displayed.

• *.Extension

Displays only the data file that was selected in the File Item setup menu and the data

type menu.

• *.*

Displays all the files in the medium.

13.17  Changing the Directory/File Name of the Storage Medium and Creating Directories

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands