YOKOGAWA ScopeCorder DL750 User Manual Download Page 114

Page: 114 / 406

13-1

IM 701210-06E

Saving and Loading Data

13.1 Floppy Disks/Zip Disks/PC Cards

Three types of built-in storage are available: floppy disk drive, Zip disk drive (DL750

only), and PC card drive (one type is selected at the time of purchase).

Floppy Disks That Can Be Used

The following types of 3.5" floppy disks can be used. You can format the disk on the

DL750/DL750P.

• 2HD

Formatted to 1.44 MB using MS-DOS.

• 2DD

Formatted to 720 KB using MS-DOS.

Inserting the Floppy Disk into the Floppy Disk Drive

With the label facing toward you, insert the disk from the side with the shutter. Insert the

disk until the eject button pops out.

Removing the Disk from the Floppy Disk Drive

Check that the access indicator is turned OFF and press the eject button.

Label side

Eject button

Access indicator

CAUTION

Removing the floppy disk while the access indicator is blinking can damage the

magnetic head of the floppy disk drive or destroy the data on the floppy disk.

General Handling Precautions of Floppy Disks

The DL750/DL750P cannot read floppy disks with bad sectors. Repair the sectors using

a PC before using those disks in the DL750/DL750P.

For the general handling precautions of the floppy disk, read the instruction manual that

came with the floppy disk.

Chapter 13

Saving and Loading Data

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands