YOKOGAWA ScopeCorder DL750 User Manual Download Page 30

Page: 30 / 406

10-14

IM 701210-06E

10.5 User-Defined Computation (Optional)

<For a description of this function, refer to page 2-48.>

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

MATH

Press the

Mode

soft key and select ON to display Math waveforms, OFF to not

display them. If you select ON, proceed to step 3.

Setting the Computation Start and End Points

Press the

Start Point/End Point

soft key to set the jog shuttle control to Start

Point.

Turn the

jog shuttle

to set the computation start point.

Likewise, set the End Point.

Setting the Computation

Press the

Setup

soft key. The Math1 to Math8 setup dialog boxes appear.

Use the

jog shuttle

and

SELECT

to select the Math waveform you wish to set.

A MathX setup dialog box opens.

Setting the Computing Operation

Use the

jog shuttle

and

SELECT

to set Operation to UserDef( ).

User-Defined Equation

Use the

jog shuttle

and

SELECT

to select UserDef( ). A menu for setting the

equation appears.

10.

Enter the equation using up to 55 characters according to the procedure given in

section 4.2. The head section (19 characters) of the entered equation is

displayed in the Expression box.

Use the jog shuttle and arrow keys
to select the desired operator.
To confirm, select ENT.

Select Math1 to Math8 and press
SELECT to enter the equation
displayed on the right side.

The contents entered from the
soft keyboard are displayed.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands