manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 182

13-69

IM 701210-06E

Saving and Loading Data

13

• Drive Letter

If the PC to which the DL750/DL750P is connected has multiple hard disks or if the

hard disk is partitioned, connecting the DL750/DL750P will cause the internal hard

disk of the DL750/DL750P to be assigned drive letters after the hard disks on the PC.

For details, see the instruction manual for the PC or the drive.

The drive letter for the DL750/DL750P cannot be changed.

Example

• The PC uses one hard disk as a single drive

Before connection

C: (HDD)

After connection

C: (HDD)

D: (DL750/DL750P)

• The PC uses one hard disk as two drives

Before connection

C: (HDD)

D: (HDD)

After connection

C: (HDD)

D: (HDD)

E: (DL750/DL750P)

Actually, this may vary depending on how the hard disk is partitioned and the type of

interface (IDE, SCSI, etc) and drive.

Note

•

The internal hard disk of the DL750/DL750P has a built-in terminator.  When the DL750/
DL750P is connected to a PC, it is recommended that the DL750/DL750P be connected to
the end of the SCSI chain.

•

Note that the driver letter assignments are different from the DL708, DL708E, and DL716.

•

Do not access the internal hard disk of the DL750/DL750P from the PC when the internal
hard disk is being accessed from the DL750/DL750P.  Likewise, do not access the internal
hard disk from the DL750/DL750P when the internal hard disk is being accessed from the
PC.

13.18  Connecting a PC to the DL750 via SCSI

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands