YOKOGAWA ScopeCorder DL750 User Manual Download Page 324

Page: 324 / 406

19-36

IM 701210-06E

Item

Specifications

Table of Cutoff Frequency Characteristics of the Anti-Aliasing Filter (AAF)

When the filter is set to Auto, the anti-aliasing filter and low-pass filter are automatically set
according to the sample rate.

Sample Rate AAF

Low-pass filter

100 kS/s

40 kHz

OFF

50 kS/s

20 kHz

OFF

20 kS/s

8 kHz

OFF

10 kS/s

4 kHz

5 kS/s

2 kHz

4 kHz

2 kS/s

800 Hz

4 kHz

1 kS/s

400 Hz

500 S/s

200 Hz

400 Hz

200 S/s

80 Hz

400 Hz

100 S/s

40 Hz

50 S/s

20 Hz

40 Hz

20 S/s to 5 S/s

20 Hz

40 Hz

2 S/s or less

20 Hz

40 Hz

Ext sample

40 kHz

OFF

Value measured under standard operating conditions (section 19.11).

BNC

Combined with the 10:1 passive probe
(701940)

Direct input (cable not complying with
the safety standard)

Typical value represents a typical or average value. It is not strictly warranted.

WARNING

• Do not apply input voltage exceeding the maximum input voltage, withstand

voltage, or allowable surge voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth

grounding of the DL750/DL750P.

• To prevent the possibility of electric shock, be sure to fasten the module screws.

Otherwise, the electrical and mechanical protection functions will not be

activated.

• Avoid continuous connection under an environment in which the allowable surge

voltage may occur.

19.12 Module Specifications

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands