manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 313

19-25

IM 701210-06E

Specifications

19

Item

Specifications

Compatible probes/cables Connection cable (for high voltage 1:1): Recommended 1

701901 (isolated type BNC-safety alligator clip adapter 

×

 2: For measuring 850 V (DC+ACpeak)

or less),
701954 (alligator clip (dolphin type) red/black 2-piece set) is required separately

Voltage probe (10:1 safety probe): Recommended 2

700929 (10:1 safety probe) .20 to 45 pF: For measuring 1000 V (DC+ACpeak) or less

Current probe (power can be supplied from the DL750/DL750P)

700937 (15 A), 701930 (150 A), 701931 (500 A), 701933 (30 A)

1.

Value measured under standard operating conditions (section 19.11).

H

L

Combined with the 700929

2.

3.

4.

700929

H

L

701901

701954

5.

6.

7.

Combined with the 701954

H

L

Direct input (cable not complying with the safety standard)

8.

9.

BNC

Withstand voltage: 3700 Vrms for 1 minute

10. Typical value represents a typical or average value.  It is not strictly warranted.

WARNING

• When applying high voltage using this module, use the 1:1 safety cable

(combination of 701901 and 701954) or the isolated probe (700929).

• The Measurement Category of the direct input of this module is 400 Vrms-CAT

II on the low side and 700 Vrms-CAT II on the high side.  Use caution because

the overvoltage category differs between the low and high sides.

• Do not apply input voltage exceeding the maximum input voltage, withstand

voltage, or allowable surge voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth

grounding of the DL750/DL750P.

• To prevent the possibility of electric shock, be sure to fasten the module screws.

Otherwise, the electrical and mechanical protection functions will not be

activated.

• Avoid continuous connection under an environment in which the allowable surge

voltage or higher voltage may occur.

19.12 Module Specifications

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands