YOKOGAWA ScopeCorder DL750 User Manual Download Page 310

Page: 310 / 406

19-22

IM 701210-06E

19.12 Module Specifications

High-Speed 10 MS/s, 12-Bit Non-Isolation Module (701255) Specifications

Item

Specifications

Standard operating

Temperature: 23

conditions

Humidity: 55%

10% RH

After a 30-minute warm-up and after calibration

Effective measurement

20 div (

10 div around 0 V, display range: 10 div, when Variable is OFF)

range

Number of input channels

Input coupling

AC, DC, and GND

Maximum sample rate

10 MS/s

Input format

Non-isolated, unbalanced

Frequency characteristics

(–3 dB point when a sine wave of amplitude

3 divisions is input)

DC to 3 MHz

Voltage-axis sensitivity

When using 10:1 probe attenuation:

50 mV/div to 200 V/div (1-2-5 steps)

setting

When using 1:1 probe attenuation:

5 mV/div to 20 V/div (1-2-5 steps)

Maximum input voltage (at a frequency of 1 kHz or less)

Combined with 701940 (10:1)

600 V (DC+ACpeak)

Direct input (1:1)

250 V (DC+ACpeak)

DC offset

5 div

maximum selectable range

Vertical (voltage) axis accuracy

DC accuracy

5 mV/div to 20 V/div:

(0.5% of 10 div)

Input connector

BNC connector (metallic type)

Input impedance

1 M

Ω ±

1%, approx. 35 pF

Lower –3 dB point when

10 Hz or less (1 Hz or less when using the 701940)

AC coupled

Common mode rejection

80 dB (50/60 Hz) or more (typical

)

ratio

Residual noise level

400 mV or

0.06 div, whichever is greater (typical

)

(Input section shorted)

A/D conversion resolution

12 bit (150 LSB/div)

Temperature coefficient

Zero point:

5 mV/div to 20 V/div:

(0.05% of 10 div)/

C (typical

)

Gain:

(0.02% of 10 div)/

C (typical

)

Bandwidth limit

Select from OFF, 500 kHz, 50 kHz, 5 kHz, and 500 Hz
Cut-off characteristics: –18 dB/OCT (typical

)

Probe attenuation setting

Voltage probe:

1:1, 10:1, 100:1, 1000:1

Current probe:

10 A:1 V (for the 700937/701933), 100 A:1 V (for the 701930/701931)

Compatible probes/cables Voltage probe (10:1 passive probe): Recommended

701940, 17 to 46 pF: For measuring 600 V (DC+ACpeak) or less

Current probe (power can be supplied from the DL750/DL750P)

700937 (15A), 701930 (150A), 701931 (500 A), 701933 (30 A)

High voltage differential probe (connect the GND cable provided with the probe to the DL750/DL750P case)

700924 (1000:1, 100:1/1400 Vpeak): For measuring 1400 Vpeak or less

Connection cable (for low voltage 1:1)

366926 (non-isolated type BNC-alligator clip

2: For measuring low voltage less than or equal to

42 Vpeak)

Value measured under standard operating conditions (section 19.11).

Recommended:
Combined with the 10:1 passive probe
(701940)

701255
Input
terminal

Earth

Direct input
(When a cable that does not comply with
the safety standard is connected)

GND is connected to the case potential.

GND

Typical value represents a typical or average value. It is not strictly warranted.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands