manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 73

11-35

IM 701210-06E

Waveform Analysis/Search

11

Automated measurement of various waveform parameters are performed on the data

stored to the acquisition memory.  Up to 48000 data points among the parameters that

are automatically measured can also be saved to a file.  (For details, see section 13.10.)

Burst1 
  Width

Distal Line (90%)

Proximal Line (10%)

Measurement Range

Set the measurement range 
(T-Range) to match the burst 
width of the signal being measured.

Burst1, Burst2: Burst Width

(Bst1, Bst2)

T1 cursor

T2 cursor

Mesial Line (50%)

Burst2 
  Width

• Other Measurement Parameters

Int1TY:

The area under the positive amplitude

Int2TY:

The area under the positive amplitude – the area under the negative

amplitude

Int1XY:

The summation of the triangular area of the X-Y waveform

Int2XY:

The summation of the trapezoidal area of the X-Y waveform

For details regarding the area calculations, see Appendix 3, “How to Calculate the Area of a
Waveform.”

Setting the Delay

The time difference between the rising or falling edges of trace waveforms or trigger

points is called the delay between channels.

Reference 
Waveform

Measurement
Waveform

1 count

N1 count

1 count

N2 count

Delay between Channels

• Edge Polarity
• Edge Count

Setting Example of Reference
Waveform

Setting Example of Measurement 
Waveform

Measurement Range

: (Rising)
: N1(1 to 9)

• Edge Polarity
• Edge Count

: (Falling)
: N2(1 to 9)

Mesial Line

• If Mode is set to Time or Degree, measurements will be made.  The default setting is

OFF.

Time:

Display the delay between channels as a time

Degree: Display the delay between channels as an angle

Degree = Delay (s)/Period (s) 

×

 360 (deg).  The period is that of a reference

waveform.

• Select   (rising edge) or   (falling) for the slope of the edge to be detected using

Edge Polarity.  The default setting is rising.

• Set the number of edges to detect before actually considering it a detection point in

Edge Count.  The range is an integer from 1 to 9.  The default value is 1.

11.6 Automated Measurement of Waveform Parameters

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands