YOKOGAWA ScopeCorder DL750 User Manual Download Page 176

Page: 176 / 406

13-63

IM 701210-06E

Saving and Loading Data

13.17 Changing the Directory/File Name of the

Storage Medium and Creating Directories

CAUTION

Never remove the storage medium (disk) or turn OFF the power while the

access indicator or the floppy disk, Zip disk, internal hard disk (optional), USB

storage device icon is blinking. Such acts can damage the storage medium or

destroy the data on the medium.

Procedure

Changing the Directory/File Name of the Storage Medium

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

FILE

Press the

Utility

soft key. The Utility setup menu and the File List window

appear.

Press the

Function

soft key. The file function selection menu is displayed.

Press the

Rename

soft key.

Selecting Media and Directories

Select the medium and directory according to steps 4 to 9 in section 13.8,

“Saving/Loading the Setup Data.”

Changing the File Attributes

Change the file attribute according to steps 6 and 7 in section 13.15, “Changing

the File Attributes and Deleting Files.”

Changing the Directory/File Name of the Storage Medium (Excluding Net Drive)

Turn the

jog shuttle

to select a directory name or file name.

Press the

File Name

soft key. A keyboard appears. The name of directory/file

is displayed in the entry box of the keyboard.

Enter the directory name or file name according to the procedure given in

section 4.2.

Specifying the Files to Be Displayed in the File List Window and Displaying Properties

10.

Carry out steps 19 to 21 in section 13.8, “Saving/Loading the Setup Data.”

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands