YOKOGAWA ScopeCorder DL750 User Manual Download Page 274

Page: 274 / 406

18-3

IM 701210-06E

Troubleshooting, Maintenance, and Inspection

18.2 Messages and Corrective Actions

Code

Message and Corrective Action

Section

Realtime recording is being prepared.

7.7

Media information is being read.

13.5

Failed to retrieve the data. Execute again.

Chapter 11

This setting not possible on DSP channels.

Chapter 15

The maximum sampling rate when using DSP channels is 5 MS/s.

Chapter 15

Slower sample rate than 2MS/s when set a DSP display.

279

This command cannot be used in the current mode.

Chapter 9

Errors in Execution (700 to 799)

Code

Message and Corrective Action

Section

701

Long copy is not possible when waveform acquisition is in progress.

7.1, 12.2

Press the START/STOP key to stop the waveform acquisition first.

703

Undo is not possible since data that existed immediately before initialization and auto setup is not

4.4, 4.5

available.

704

Can not be executed while running. Press START/STOP key to stop acquisition.

7.1

707

Can not Start while data out. Wait until output is completed.

7.1

708

Can not data out while running. Press START/STOP key to stop acquisition.

7.1

709

Can not detect listener. Check GP-IB connector.

–

710

File not found. Check the file.

Chapter 13

711

Cannot manipulate files while image printing is in progress. Wait until image printing is complete.

Chapter 13

712

Can not compress this hardcopy image. Turn off compression switch.

13.11

713

Calibration failure. Disconnect the input and execute again.

4.6

If it fails again, servicing is necessary.

714

Temperature module calibration failed. Calibration value is invalid. Check the input signal.

4.6

716

Realtime recording to the internal hard disk is valid when the sampling rate is slower than the values

7.7

shown below.
1~2 CH : 100 kS/s, 3CH : 50 kS/s,
4~5CH : 20 kS/s, 6~11CH : 10 kS/s,
12~18CH : 5 kS/s

717

Too many channels for the current T/div setting to realtime record.

7.7

Decrease the number of channels by turning them OFF.

718

Too many channels to realtime record at the current record length.

7.7

Turn OFF channels to reduce the number of channels or shorten the record length.

721

Can not operate while data out. Wait until output is completed.

7.7

723

Cannot load the realtime record.

7.7,13.14

724

Balancing failed.

–

* indicates the channel number of the channel for which automatic balancing failed.

725

Cannot be executed. Acquisition not active.

7.1

727

Insufficient output data. Increase Mag or widen the Time Range interval.

12.2

728

Image is being printed. Abort or wait until printing is complete.

Chapter 13

730

Pattern is not specified.

11.4

732

Cannot be executed while computation is in progress.

Chapter 10

733

Failed to measure statistics.

11.7

Waveform data may be missing.
If Cycle Statistics is specified, the instrument may be configured in a way that fails to detect the cycle.

735

Executing file Load, Save, or Format. Abort or wait until it is complete.

Chapter 13

736

Image is being printed or saved. Abort the operation or wait until the execution of the command is

Chapter 13

complete.

737

A setup of an action trigger can’t be carried out under the state of on.

6.18

738

Cannot be executed when the dual capture setting is ON.

7.6

739

Cannot be executed when realtime record or print setting is ON.

7.7

740

A time base can’t be carried out under the state of the outside clock.

5.14

741

A start by the START key can’t be done in the GO-NOGO mode.

11.8, 11.9

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands