YOKOGAWA ScopeCorder DL750 User Manual Download Page 326

Page: 326 / 406

19-38

IM 701210-06E

Item

Specifications

Input voltage range (

FS)

When using 1:1 probe attenuation:

1 V,

2 V,

5 V,

10 V,

20 V,

50 V (

FS)

When using 10:1 probe attenuation:

10 V,

20 V,

50 V,

100 V,

200 V,

500 V (

FS)

(combined with the recommended probe 700929)

Input impedance

1 M

Ω ±

1%, approx. 35 pF

Pull-up function: 4.7 k

Ω

, approx. 5 V (pull-up can be turned ON only when the input is set to Pull-Up 5V)

Input coupling settings

AC and DC

Probe attenuation setting

10:1 and 1:1

Minimum voltage width for 200 mV

P-P

pulse detection

Bandwidth limit

Select from Full, 100 kHz, 10 kHz, 1 kHz, and 100 Hz
Cutoff characteristics: –12 dB/OCT (typical

)

Threshold

Set within the FS of the voltage range. Set in units of 1% of the FS.

Hysteresis

Select

1%,

2.5%, or

5% of the FS of the voltage range

Preset function

Logic (5V/3V/12V/24V), electromagnetic pickup, zero crossing, pull-up, AC100V, AC200V, and
user-defined

Slope selection

Select rising or falling

Lower –3 dB point when

0.5 Hz or less (0.05 Hz or less when using the 700929) (typical

)

AC coupled

Chatter elimination function OFF or 1 to 1000 ms (1 ms resolution)

Eliminates the chatter that occurs such when the contact input is turned ON/OFF. Can discard the
signal changes over the specified interval.

Input status indication

Input status indication through the LEDs of each channel

function

When in operation:

Illuminates in green when pulse input is detected

When overdriven:

Illuminates in red when the input voltage exceeds the range

Compatible probes/cables Connection cable (1:1): Recommended 1

366926

Voltage probe (10:1 safety probe): Recommended 2

700929 (10:1 safety probe) .20 to 45 pF: For measuring 1000 V (DC+ACpeak) or less

Value measured under standard operating conditions (section 19.11).

Combined with the 700929

700929

Direct input (cable not complying with the safety standard)

BNC

Withstand voltage: 1500 Vrms for 1 minute
Allowable transient surge voltage (between earth and input):

2100 Vpeak

Input waveform of 1 Vpp, rectangular wave, rise/fall time within 1 ms (input range:

10 V, bandwidth limit: Full, and

hysteresis:

1%)

Input waveform of 90 Vrms, sine wave (input range: AC100V, bandwidth limit 100 kHz, and hysteresis:

1%)

Input waveform of 1 Vpp, rectangular wave, rise/fall time within 5 ns (input range:

10 V, bandwidth limit: Full, and

hysteresis:

1%)

Typical value represents a typical or average value. It is not strictly warranted.

WARNING

• Do not apply input voltage exceeding the maximum input voltage, withstand

voltage, or allowable surge voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth

grounding of the DL750/DL750P.

• To prevent the possibility of electric shock, be sure to fasten the module screws.

Otherwise, the electrical and mechanical protection functions will not be activated.

• Avoid continuous connection under an environment in which the allowable surge

voltage may occur.

19.12 Module Specifications

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands