YOKOGAWA ScopeCorder DL750 User Manual Download Page 225

Page: 225 / 406

16-14

IM 701210-06E

16.5 Sending Periodic Mail or Action Mail (SMTP

Client Function

<For a description of this function, refer to page 2-60.>

Procedure

Sending Periodic E-mail Messages

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

FILE

SHIFT

HELP

MISC

NUM KEY

Press

MISC

Press the

Network

soft key.

Press the

Mail Setup

soft key. The Mail setup menu appears.

Setting the Mail Server

Use the

jog shuttle

and

SELECT

to select Mail Server.

Enter the IP address of the mail server according to the procedure given in

section 4.2. If you are using DNS, you can specify the mail server by name.

Setting the Recipient Mail Address

Use the

jog shuttle

and

SELECT

to select Mail Address.

Enter the recipient mail address using up to 40 characters according to the

procedure given in section 4.2.

Setting a Comment

Use the

jog shuttle

and

SELECT

to select Comment.

As necessary, enter the comment using up to 30 characters according to the

procedure given in section 4.2.

Setting the Time When the Mail Is to Be Sent

10.

Use the

jog shuttle

and

SELECT

to select the hour, minute, or second of

MailBaseTime

11.

Enter the time when mail is to be sent according to the procedure given in

section 4.2.

Setting the Attached Image File

12.

Use the

jog shuttle

and

SELECT

to select ON (attach image file) or OFF (do

not attach image file).

Setting the Interval for Sending Mail

13.

Use the

jog shuttle

and

SELECT

to select Interval.

14.

Select the interval for sending mail in the range of 1 h to 24 h according to the

procedure given in section 4.2.

Sending a Test Mail

15.

Turn the

jog shuttle

to move the cursor to Mail Test.

To send a test mail to the specified recipient, press

SELECT

While mail transmission is in progress,

is indicated at the upper left corner

of the screen.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands