manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 89

11-51

IM 701210-06E

Waveform Analysis/Search

11

• Setting the Number of Actions

13.

Use the 

jog shuttle

 and 

SELECT

 to set Sequence to Single or Continue.

• Setting the Number of Determinations

14.

Use the 

jog shuttle

 and 

SELECT

 to set ACQ Count.

• Enabling/Disabling the External Input Signal

15.

Use the 

jog shuttle

 and 

SELECT

 to set Remote to OFF or ON.

Selecting the Action

16.

Press the 

Action

 soft key.

17.

Use the 

jog shuttle

 and 

SELECT

 to set each action ON/OFF.

18.

If you turn ON Save to File in step 17, use the 

jog shuttle 

and 

SELECT 

to set

the file save format to Binary, ASCII, or Float.

Setting the Determination Range

19.

Press the 

Time Range1/Time Range2

 soft key to set the jog shuttle control to

Time Range1.

20.

Turn the 

jog shuttle

 to set the determination start point.

21.

Likewise, set Time Range2 (determination end point).

Executing the GO/NO-GO Determination

22.

Press the 

Exec

 soft key to execute the GO/NO-GO determination.  The soft key

changes to 

Abort

.  Waveform acquisition stops automatically, when

determination is finished,

To stop the GO/NO-GO determination, press the 

Abort

 soft key or 

START/

STOP

.

In addition, if the following action is specified, the following icon is displayed at

the upper left corner of the screen when an action is activated.

Image/Save to File:

Save destination medium (

 FD, 

 Zip disk, 

 PC

card, 

 external SCSI device, 

 internal HD, 

network drive, or 

 USB storage device)

Send Mail:

11.9 GO/NO-GO Determination Using Measured Waveform Parameters

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands