YOKOGAWA ScopeCorder DL750 User Manual Download Page 2

Page: 2 / 406

Part 2:i

IM 701210-06E

4th Edition : May 2009 (YK)

Thank you for purchasing the DL750/DL750P ScopeCorder.

This user’s manual contains useful information about the instrument’s functions and

operating procedures and lists the handling precautions of the DL750/DL750P. It mainly

focuses on the DL750. The user’s manual is divided into two parts, Part 1 and Part 2.

For details on the information covered in Part 1 and Part 2 as well as other DL750/

DL750P manuals, see “Manuals That Come with the DL750/DL750P” on the next page.

To ensure correct use, please read this manual thoroughly before beginning operation.

After reading the manual, keep it in a convenient location for quick reference whenever a

question arises during operation.

Notes

• The contents of this manual are subject to change without prior notice as a result of

continuing improvements to the instrument’s performance and functions. The figures

given in this manual may differ from those that actually appear on your screen.

• Every effort has been made in the preparation of this manual to ensure the accuracy

of its contents. However, should you have any questions or find any errors, please

contact your nearest YOKOGAWA dealer.

• Copying or reproducing all or any part of the contents of this manual without the

permission of Yokogawa Electric Corporation is strictly prohibited.

• The TCP/IP software of this product and the document concerning the TCP/IP

software have been developed/created by YOKOGAWA based on the BSD

Networking Software, Release 1 that has been licensed from University of California.

Trademarks

• Microsoft, Internet Explorer, MS-DOS, Windows, Windows NT, and Windows XP are

either registered trademarks or trademarks of Microsoft Corporation in the United

States and/or other countries.

• Adobe, Acrobat, and PostScript are trademarks of Adobe Systems Incorporated.

• Zip is either a registered trademark or trademark of Iomega Corporation in the United

States and/or other countries.

• UNIX is either a registered trademark or trademark of The Open Group in the United

States and/or other countries.

• Piezotron is a registered trademark of Kistler Instrument Corporation.

• ICP is a registered trademark of PCB Piezotronics Incorporated.

• ISOTRON is a registered trademark of ENDEVCO Corporation.

• GIGAZoom ENGINE are pending trademark of Yokogawa Electric Corporation.

• For purposes of this manual, the TM and ® symbols do not accompany their

respective trademark names or registered trademark names.

• Other company and product names are trademarks or registered trademarks of their

respective holders.

Revisions

• 1st Edition:

February 2005

• 2nd Edition: May 2005

• 3rd Edition:

December 2005

• 4th Edition:

May 2009

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands