YOKOGAWA ScopeCorder DL750 User Manual Download Page 315

Page: 315 / 406

19-27

IM 701210-06E

Specifications

19.12 Module Specifications

Item

Specifications

Input impedance

Approx. 1 M

Ω

Common mode rejection

[Voltage measurement] 80 dB (50/60 Hz) or more (typical

)

ratio

[Temperature measurement] 120 dB or more (50/60 Hz, with 2-Hz filter ON, signal source
resistance of 500

Ω

or less) (typical

)

Residual noise level

[Voltage measurement]:

100

V or

0.01 div, whichever is greater (typical

)

(Input section shorted)

A/D conversion resolution

[Voltage measurement] 16 bits (2400 LSB/div)

Temperature coefficient

[Voltage measurement] Zero point:

(0.01% of 10 div)/

C (typical

)

Gain:

(0.02% of 10 div)/

C (typical

)

Reference junction compensation accuracy (when the input terminal temperature is balanced)

K, E, J, T, L, U, N:

R, S, B, W:

1.5

Au7Fe:

Bandwidth limit

[Temperature measurement] (Digital analog filter)

Select from OFF, 30 Hz, 8 Hz, and 2 Hz + 150 Hz secondary analog filter

[Voltage measurement]

Select from OFF, AUTO, 4 kHz, 400 Hz, or 40 Hz.
Cutoff characteristics: –12 dB/OCT (typical

, setting other than AUTO)

Cutoff frequency (fc) when set to AUTO (701262 only)

Sample Rate

Cutoff Frequency (fc)

100 kHz or higher

40 kHz

100 Hz to 50 kHz

40% of the sample rate

50 Hz or less

20 Hz

Cutoff characteristics for AUTO: –65 dB at 2

fc (typical

)

Table of cutoff frequency characteristics of the anti-aliasing filter (AAF)

When the filter is set to Auto, the anti-aliasing filter and low-pass filter are automatically set
according to the sample rate.

Sample Rate

AAF

Low-Pass Filter

100 kS/s

40 kHz

OFF

50 kS/s

20 kHz

OFF

20 kS/s

8 kHz

OFF

10 kS/s

4 kHz

5 kS/s

2 kHz

4 kHz

2 kS/s

800 Hz

4 kHz

1 kS/s

400 Hz

500 S/s

200 Hz

400 Hz

200 S/s

80 Hz

400 Hz

100 S/s

40 Hz

50 S/s

20 Hz

40 Hz

20 S/s to 5 S/s

20 Hz

40 Hz

2 S/s or less

20 Hz

40 Hz

Ext sample

40 kHz

OFF

Value measured under standard operating conditions (section 19.11).

Does not include the reference junction temperature compensation accuracy.

This module supports Au7Fe with 0.07% metal content with respect to gold.

Typical value represents a typical or average value. It is not strictly warranted.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands