YOKOGAWA ScopeCorder DL750 User Manual Download Page 245

Page: 245 / 406

16-34

IM 701210-06E

16.7 Using the Web Server Function

Saving the Screen Image in the PC

Right-click on the screen image that is displayed. A shortcut menu appears as shown

in the following figure. Choose

Save Picture As

to save the current screen image.

• Saving Data in the PC and Loading Setup Data from the PC into the DL750/

DL750P (Data Control)

Saving Data in the PC (Capture)

Data Type

Select the type of data to be saved from Waveform Binary, Waveform ASCII,

Waveform Float, Setup, and Measure. For details on the settings, see the

explanations in section 13.7, 13.8, and 13.10.

Capture Exec

Using the dialog box that appears when you click Capture Exec, set the save

destination and file name and save the data.

Abort

To abort the save operation while data is being saved, click Cancel on the dialog

box. Then, click Abort on the Control Panel.

You must enter a password to abort.
For details, see “Input Password” in
the next section.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands