YOKOGAWA ScopeCorder DL750 User Manual Download Page 226

Page: 226 / 406

16-15

IM 701210-06E

Ethernet Interface (Optional)

16.5 Sending E-mail Messages (Periodic Mail or Action Mail)

Note

•

For keyboard (soft keyboard) operation, see section 4.2, “Entering Values and Strings.”

•

The sender (From) address of the e-mail messages sent by the DL750/DL750P is the
same as the specified recipient address.

•

If the transmitted contents indicate error logs, the most recent error is at the top of the
error log.

•

To use this function, configure the TCP/IP settings beforehand according to section 16.2,
“Setting up the TCP/IP.”

•

If you set Interval to OFF, periodic mail is not sent.

Sending Action E-mail Messages

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

FILE

SHIFT

HELP

MISC

NUM KEY

Set items according to steps 1 to 9 in “Sending Periodic E-mail Messages.”

You do not have to set MailBaseTime and Interval for action mail. If you wish to

use only action mail, set Interval to OFF.

Setting the Action

• From the ACTION Menu

Press

SHIFT+MODE

Press the

Mode

soft key to select

ON Trigger

Press the

Action

soft key. The action setup menu appears.

Use the

jog shuttle

and

SELECT

to set Send Mail to ON.

Use the

jog shuttle

and

SELECT

to set Mail Count (the number of mail

messages).

Press

START/STOP

to start the waveform acquisition. A mail is sent to the

specified address each time a trigger occurs.

While mail transmission is in progress,

is indicated at the upper left corner

of the screen.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands