YOKOGAWA ScopeCorder DL750 User Manual Download Page 270

Page: 270 / 406

17-6

IM 701210-06E

17.5 Turning OFF the Backlight and Setting the

Brightness of the Backlight

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

FILE

SHIFT

HELP

MISC

NUM KEY

Press

MISC

Press the

Next 1/2

soft key.

Press the

LCD

soft key. The LCD setup menu appears.

Setting Backlight Auto Off

Press the

Auto OFF

soft key to select ON or OFF.

If you set Auto OFF to ON, proceed to step 5.

Press the

Auto OFF Time

soft key.

Turn the

jog shuttle

to set the time when the backlight will automatically turn

OFF.

Setting the Backlight Brightness

Press the

Brightness

soft key.

Turn the

jog shuttle

to set the backlight brightness.

Turning ON/OFF the Backlight

Press the

LCD OFF Exec

soft key. The backlight turns OFF.

Press any key to return to the measurement screen.

Explanation

Turning ON/OFF the Backlight: LCD OFF Exec

Turns ON/OFF the LCD backlight. If a key is pressed when the backlight is OFF, the

screen returns to the measurement screen.

Setting the Backlight Auto OFF: Auto OFF, Auto OFF Time

The backlight automatically turns OFF, if there is no key operation for the specified time.

Setting the Backlight Brightness

You can change the brightness of the backlight. Set the brightness in the range of 0

(darkest) to 7 (brightest).

The lifetime of the backlight can be prolonged by dimming the backlight or turning OFF

the backlight when it is not necessary.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands