Yamaha RCX141 User Manual Download Page 180 | Manualshive

Page: 180 / 402

background image

4-

122

Operation

4

11. “MANUAL” mode

11.6.1.1 Restoring hand definitions

[Procedure]

1) During hand definition editing, pressing the

F 1

(UNDO) key reverses the last

data input and restores the preceding data.
This function is enabled only on lines that are not yet complete.

11.6.2

Hand definition setting method 1

By using this method, a hand attached to the 2nd arm can be set to the current hand
definition.

[Procedure]

1) In “MANUAL>HAND” mode, use the cursor (

↑

/

↓

) key to select the hand definition

number.

2) Press the

F 6

(METHOD1) key to enter “MANUAL>HAND> METHOD1”

mode.

Fig. 4-11-78 Hand setting 1 (1)

MANUAL

>HAND>METHOD1 50% [MG][S0H0X]

————————————1———————2———————3———————4———

Move arm to P[1] and press ENTER key

1st P=

2nd P=

[POS] 600.00 0.00 0.00 0.00

VEL+

VEL-

3) Use the Jog keys to move the robot working point to point 1.

(Position it accurately.)

4) Press the

key to enter the teaching value.

Fig. 4-11-79 Hand setting 1 (2)

MANUAL

>HAND>METHOD1 50% [MG][S0H0X]

————————————1———————2———————3———————4———

Move arm to P[2] and press ENTER key

1st P= 214.45 -15.01 20.32

2nd P=

[POS] 214.45 -15.01 20.32 0.00

VEL+

VEL-

n

NOTE

• Cartesian and SCARA robots use

mutually different methods for
making settings.

Cartesian robots

Hand definition data is set by
teaching the identical points that
are used for hand working points
and non-hand working points.

SCARA robots

Hand definition data is set by
teaching the identical points that
are used at working points for
right-handed and left-handed
systems.

• When two robots (main and sub

robots) are specified, check the
currently selected robot group on
the MPB screen. “[MG]”
indicates the main robot group
and “[SG]” the sub robot group.
Switch the robot group with the

ROBOT key (

LOWER

+

MODE

) as

needed.

w

WARNING

The robot starts to move when a
Jog key is pressed. To avoid
danger, do not enter the robot
movement range.

n

NOTE

To perform teaching at point 1 with a
SCARA robot, always move in the
right-hand system.
To perform teaching at point 2 with a
SCARA robot, always move in the left-
handed system.

«
...
178
179
180
181
182
...
»

Summary of Contents for RCX141



















































































































































































































































































































































































































Reviews:

No comments

Related manuals for RCX141

Brand: GBD Pages: 12

Brand: Acclaim Lighting Pages: 32

Brand: Jeep Pages: 19

Brand: Laars Pages: 28

Brand: Harsco Industrial Pages: 57

Brand: Lamtec Pages: 136

Gemini GEM-P9600

Brand: NAPCO Pages: 6

Gemini GEM-P816

Brand: NAPCO Pages: 56

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 11

Brand: Nauticam Pages: 2

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 20

GEMINI C Series

Brand: NAPCO Pages: 24

Brand: iluminize Pages: 2

Brand: Zaiput Flow Technologies Pages: 10

Centronic SunWindControl SWC245-II

Brand: Becker Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands