SmartPAC 2 with WPC 2000 Integration User Manual
1128600
Run Mode
6-51
Continuous, Two-hand Operation
To run the press in Continuous, Two-hand mode, do the following:
1.
With “TWO HAND” highlighted on the Mode Select Menu, press the Prior Act button on
the Operator Station, then, within 8 seconds, press both Run/Inch palm buttons and hold
them through the Auto Carry-up Angle. The ram will complete the stroke and continue
stroking until one of the following events occurs:
•
You press the Top Stop button
•
You press the Emergency Stop button
•
A system fault is detected
•
The light curtain is blocked during the non-muted portion of the stroke
The ram will stop in mid-stroke if you do not hold the Run/Inch palm buttons through the
Auto Carry-up Angle.
Continuous, Foot Operation
Continuous, Foot operation can only be used with WPC 2000 systems running Two-hand/
One-hand/Foot firmware and employing a Shadow light curtain to guard the point of
operation.
Option switch 3 settings, which govern Foot operation in Single-stroke (see page 6-48), do not
apply to Continuous, Foot operation.
To run the press in Continuous, Foot mode, do the following:
You must press both Run/Inch palm buttons on the Operator Station within 8 seconds after you
press the Prior Act button in order to initiate Continuous mode operation. Otherwise, the press will
not start. The Prior Act lamp illuminates when you press the Prior Act button and turns off after 8
seconds.
If the press is Emergency-stopped, WPC 2000 automatically changes to Two-hand
Maintained Single-stroke mode and the “Interrupted Stroke” message flashes on the
SmartPAC 2 display. To clear the “Interrupted Stroke” message, press and hold both Run/
Inch buttons to complete the stroke and return the ram to Top-stop.
INCORRECT INSTALLATION
You must install a Shadow light curtain correctly and connect it to WPC 2000 properly in order to
run the press in Continuous, Foot mode.
Failure to comply with these instructions will result in death or serious injury.
NOTICE
NOTICE
DANGER
!
Summary of Contents for SmartPAC 2
