manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

896/1080

RM0365

Universal synchronous asynchronous receiver transmitter (USART)

901

Bit 9

CTSIF

: CTS interrupt flag

This bit is set by hardware when the CTS input toggles, if the CTSE bit is set. It is cleared by 
software, by writing 1 to the CTSCF bit in the USART_ICR register. 
An interrupt is generated if CTSIE=1 in the USART_CR3 register.
0: No change occurred on the CTS status line
1: A change occurred on the CTS status line

Note: If the hardware flow control feature is not supported, this bit is reserved and forced by 

hardware to ‘0’.

Bit 8

LBDF

: LIN break detection flag

This bit is set by hardware when the LIN break is detected. It is cleared by software, by 
writing 1 to the LBDCF in the USART_ICR. 
An interrupt is generated if LBDIE = 1 in the USART_CR2 register.
0: LIN Break not detected
1: LIN break detected

Note: If the USART does not support LIN mode, this bit is reserved and forced by hardware 

to ‘0’. Please refer to 

Section 29.4: USART implementation on page 837

.

Bit 7

TXE

: Transmit data register empty

This bit is set by hardware when the content of the USART_TDR register has been 
transferred into the shift register. It is cleared by a write to the USART_TDR register.
The TXE flag can also be cleared by writing 1 to the TXFRQ in the USART_RQR register, in 
order to discard the data (only in Smartcard T=0 mode, in case of transmission failure). 
An interrupt is generated if the TXEIE bit =1 in the USART_CR1 register. 
0: data is not transferred to the shift register
1: data is transferred to the shift register)

Note: This bit is used during single buffer transmission.

Bit 6

TC

: Transmission complete

This bit is set by hardware if the transmission of a frame containing data is complete and if 
TXE is set. An interrupt is generated if TCIE=1 in the USART_CR1 register. It is cleared by 
software, writing 1 to the TCCF in the USART_ICR register or by a write to the USART_TDR 
register.
An interrupt is generated if TCIE=1 in the USART_CR1 register. 
0: Transmission is not complete
1: Transmission is complete

Note: If TE bit is reset and no transmission is on going, the TC bit will be set immediately.

Bit 5

RXNE

: Read data register not empty

This bit is set by hardware when the content of the RDR shift register has been transferred 
to the USART_RDR register. It is cleared by a read to the USART_RDR register. The RXNE 
flag can also be cleared by writing 1 to the RXFRQ in the USART_RQR register. 
An interrupt is generated if RXNEIE=1 in the USART_CR1 register.
0: data is not received
1: Received data is ready to be read.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

LaCie 5big Network 2 Datasheet preview
5big Network 2
Brand: LaCie Pages: 4
LaCie d2 Network 2 Datasheet preview
d2 Network 2
Brand: LaCie Pages: 4
Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Brand: Raritan Pages: 4
IAR SYSTEMS IAR KickStart Kit TWR-K60N512-IAR Getting Started Manual preview
IAR KickStart Kit TWR-K60N512-IAR
Brand: IAR SYSTEMS Pages: 8
HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
Point of View SmartTV 210 User Manual preview
SmartTV 210
Brand: Point of View Pages: 13
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Brand: Danville Signal Processing Pages: 35
R3 Bridge E User Manual preview
Bridge E
Brand: R3 Pages: 48
Adaptec Ultra Wireless AWN-8030 User Manual preview
Ultra Wireless AWN-8030
Brand: Adaptec Pages: 57
A-Trend OPTI495XLC VL-BUS 3/486 Manual preview
OPTI495XLC VL-BUS 3/486
Brand: A-Trend Pages: 16
Costar CR4020XDI Installation Manual preview
CR4020XDI
Brand: Costar Pages: 24
Extron electronics EDID 101H 4K PLUS User Manual preview
EDID 101H 4K PLUS
Brand: Extron electronics Pages: 35
soundsation DCX NET Series User Manual preview
DCX NET Series
Brand: soundsation Pages: 47
Dell A2463645 - 2 GB Memory Manuallines preview
A2463645 - 2 GB Memory
Brand: Dell Pages: 2
MikroTik RBM11G Quick Start Manual preview
RBM11G
Brand: MikroTik Pages: 4
Huawei CR-P4CF Specifications preview
CR-P4CF
Brand: Huawei Pages: 2
Omniflex Maxiflex P3 CPU Installation Manual preview
Maxiflex P3 CPU
Brand: Omniflex Pages: 2

Brands by name

Popular brands

Load more brands