manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

410/1080

RM0365

Comparator (COMP)

422

17.3.3 

COMP reset and clocks

The COMP clock provided by the clock controller is synchronous with the PCLK2 (APB2 
clock).

There is no clock enable control bit provided in the RCC controller. To use a clock source for 
the comparator, the SYSCFG clock enable control bit must be set in the RCC controller.

Note:

Important: 

The polarity selection logic and the output redirection to the port works 

independently from the PCLK2 clock. This allows the comparator to work even in Stop 
mode.

17.3.4 Comparator 

LOCK 

mechanism

The comparators can be used for safety purposes, such as over-current or thermal 
protection. For applications having specific functional safety requirements, it is necessary to 
insure that the comparator programming cannot be altered in case of spurious register 
access or program counter corruption.

Table 103. STM32F302x6/8 comparator input/outputs summary

Comparator input/outputs

COMP2

COMP4

COMP6

Comparator inverting 

Input: connection to 

internal signals

DAC1_CH1

Vrefint

¾ Vrefint
½ Vrefint
¼ Vrefint

Comparator Inputs 

connected to I/Os 

(+: non inverting input; 

-: inverting input)

+: PA7

-: PA2
-: PA4

+: PB0

-: PB2

-: PA4

+: PB11

-: PB15

-: PA4

Comparator outputs 

(motor control 

protection)

T1BKIN 

T1BKIN2

Outputs on I/Os

PA2

PA12

PB12

PB1

PA10

PC6

Outputs to internal 

signals

TIM1_OCREF_CLR

TIM1_IC1
TIM2_IC4

TIM2_OCREF_CLR

TIM15_OCREF_CLR

TIM15_IC2

 

TIM2_IC2

TIM2_OCREF_CLR

TIM16_OCREF_CLR

TIM16_IC1

 

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Brand: Taiwan Commate Computer Inc. Pages: 25
Greenlee 910FS Instruction Manual preview
910FS
Brand: Greenlee Pages: 52
Vista VIPER H4 User Manual preview
VIPER H4
Brand: Vista Pages: 93
ICP DAS USA PIO-821 Series User Manual preview
PIO-821 Series
Brand: ICP DAS USA Pages: 62
Terasic Cypress CapSense P0080 User Manual preview
Cypress CapSense P0080
Brand: Terasic Pages: 22
NETGEAR ReadyNAS Duo v2 Software Manual preview
ReadyNAS Duo v2
Brand: NETGEAR Pages: 100
Allied Telesis AT-TN109-A Specifications preview
AT-TN109-A
Brand: Allied Telesis Pages: 2
Dahua Technology NVR52A16-16P-4KS2 Quick Start Manual preview
NVR52A16-16P-4KS2
Brand: Dahua Technology Pages: 13
Belkin Wireless G F5D7000 User Manual preview
Wireless G F5D7000
Brand: Belkin Pages: 252
A-Trend OPTI495XLC VL-BUS 3/486 Manual preview
OPTI495XLC VL-BUS 3/486
Brand: A-Trend Pages: 16
Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W Series Specifications preview
Scalable Multi-Graphic Videowall Processors MGP 464W Series
Brand: Extron electronics Pages: 2
Huawei Quidway S6500 Series Command Manual preview
Quidway S6500 Series
Brand: Huawei Pages: 845
Swann NVR-7072 Instruction Manual preview
NVR-7072
Brand: Swann Pages: 30
3Com Switch 5500G-EI PWR 48-Port Specifications preview
Switch 5500G-EI PWR 48-Port
Brand: 3Com Pages: 8
3Com 3C421600A Release Note preview
3C421600A
Brand: 3Com Pages: 10
IDT 8A3 Series Programming Manual preview
8A3 Series
Brand: IDT Pages: 340

Brands by name

Popular brands

Load more brands