manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

886/1080

RM0365

Universal synchronous asynchronous receiver transmitter (USART)

901

Note:

The 3 bits (CPOL, CPHA, LBCL) should not be written while the transmitter is enabled.

29.8.3 

Control register 3 (USART_CR3)

Address offset: 0x08

Reset value: 0x0000

         

         

Bit 5

LBDL

: LIN

 

break detection length

This bit is for selection between 11 bit or 10 bit break detection.
0: 10-bit break detection
1: 11-bit break detection
This bit can only be written when the USART is disabled (UE=0).

Note: If LIN mode is not supported, this bit is reserved and forced by hardware to ‘0’. Please refer to 

Section 29.4: USART implementation on page 837

.

Bit 4

ADDM7

:7-bit Address Detection/4-bit Address Detection

This bit is for selection between 4-bit address detection or 7-bit address detection. 
0: 4-bit address detection
1: 7-bit address detection (in 8-bit data mode)
This bit can only be written when the USART is disabled (UE=0)

Note: In 7-bit and 9-bit data modes, the address detection is done on 6-bit and 8-bit address 

(ADD[5:0] and ADD[7:0]) respectively.

Bits 3:0 Reserved, must be kept at reset value.

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

WUFIE

WUS

SCARCNT2:0]

Res.

rw

rw

rw

rw

rw

rw

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

DEP

DEM

DDRE

OVR 

DIS

ONE 

BIT

CTSIE

CTSE

RTSE

DMAT

DMAR

SCEN

NACK HDSEL

IRLP

IREN

EIE

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

v

v

rw

rw

rw

rw

Bits 31:25 Reserved, must be kept at reset value.

Bit 24 Reserved, must be kept at reset value.

Bit 23 Reserved, must be kept at reset value.

Bit 22

WUFIE

: Wakeup from Stop mode interrupt enable

This bit is set and cleared by software.
0: Interrupt is inhibited
1: An USART interrupt is generated whenever WUF=1 in the USART_ISR register

Note: WUFIE must be set before entering in Stop mode.

The WUF interrupt is active only in Stop mode.
If the USART does not support the wakeup from Stop feature, this bit is reserved and 
forced by hardware to ‘0’.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

D-Link ShareCenter Quattro DNS-345 Quick Install Manual preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 40
D-Link ShareCenter Quattro DNS-345 Datasheet preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 4
D-Link MYDLINK DNR-322L Datasheet preview
MYDLINK DNR-322L
Brand: D-Link Pages: 4
D-Link mydlink DNR-312L Quick Install Manual preview
mydlink DNR-312L
Brand: D-Link Pages: 8
D-Link DNS-722-4 Quick Install Manual preview
DNS-722-4
Brand: D-Link Pages: 16
D-Link DNS-722-4 User Manual preview
DNS-722-4
Brand: D-Link Pages: 88
IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Brand: IBM Pages: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 78
IBM 9040-MR9 Manual preview
9040-MR9
Brand: IBM Pages: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Brand: IBM Pages: 132
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
NEC N8141-75F Startup Manual preview
N8141-75F
Brand: NEC Pages: 6
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
Amperes iPX5500 Instruction Manual preview
iPX5500
Brand: Amperes Pages: 8
Edge-Core SDW100 Quick Start Manual preview
SDW100
Brand: Edge-Core Pages: 7
Lorex LNR100 SERIES Instruction Manual preview
LNR100 SERIES
Brand: Lorex Pages: 186
Zonet ZUN2200 Quick Installation Manual preview
ZUN2200
Brand: Zonet Pages: 2

Brands by name

Popular brands

Load more brands