manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Analog-to-digital converters (ADC)

RM0365

389/1080

DocID025202 Rev 7

15.6.3 

ADC common regular data register for dual mode 
(ADCx_CDR, x=12)

Address offset: 0x0C (this offset address is relative to the master ADC base a 
0x300)

Reset value: 0x0000 0000

         

         

15.6.4 

ADC register map

The following table summarizes the ADC registers.

         

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

RDATA_SLV[15:0]

r

r

r

r

r

r

r

r

r

r

r

r

r

r

r

r

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

RDATA_MST[15:0]

r

r

r

r

r

r

r

r

r

r

r

r

r

r

r

r

Bits 31:16

RDATA_SLV[15:0]:

 Regular data of the slave ADC

In dual mode, these bits contain the regular data of the slave ADC. Refer to 

Section 15.3.29: 

Dual ADC modes (STM32F302xB/C/D/E only)

.

The data alignment is applied as described in 

Section : Data register, data alignment and 

offset (ADCx_DR, OFFSETy, OFFSETy_CH, ALIGN)

)

Bits 15:0

RDATA_MST[15:0]

: Regular data of the master ADC.

In dual mode, these bits contain the regular data of the master ADC. Refer to 

Section 15.3.29: 

Dual ADC modes (STM32F302xB/C/D/E only)

.

The data alignment is applied as described in 

Section : Data register, data alignment and 

offset (ADCx_DR, OFFSETy, OFFSETy_CH, ALIGN)

)

In MDMA=0b11 mode, bits 15:8 contains SLV_ADC_DR[7:0], bits 7:0 contains 
MST_ADC_DR[7:0].

Table 96. ADC global register map

(1)

Offset

Register

0x000 - 0x04C

Master ADC1

0x050 - 0x0FC

Reserved

0x100 - 0x14C

Slave ADC2

0x118 - 0x1FC

Reserved

0x200 - 0x24C

Reserved

0x250 - 0x2FC

Reserved

0x300 - 0x308

Master and slave ADCs common registers (ADC12)

1. The gray color is used for reserved memory addresses.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
MC PCIe-DIO96H User Manual preview
PCIe-DIO96H
Brand: MC Pages: 21
ADS Technologies PTV-352-EFG Hardware Quickmanual preview
PTV-352-EFG
Brand: ADS Technologies Pages: 1
TDK HHM Series HHM2245SA1 Specifications preview
HHM Series HHM2245SA1
Brand: TDK Pages: 2
Caen A 1735 Technical Information Manual preview
A 1735
Brand: Caen Pages: 14
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Brand: Magma Pages: 74
IBM Power System S914 Installing Instructions preview
Power System S914
Brand: IBM Pages: 48
Intel CORE 2 DUO E4000 - 3-2008 Datasheet preview
CORE 2 DUO E4000 - 3-2008
Brand: Intel Pages: 122
Corsair ELITE LCD UPGRADE KIT Manual preview
ELITE LCD UPGRADE KIT
Brand: Corsair Pages: 11
Rimage CDPR3 User Manual preview
CDPR3
Brand: Rimage Pages: 30

Brands by name

Popular brands

Load more brands