STMicroelectronics RM0365 Reference Manual Download Page 786 | Manualshive

Page: 786 / 1080

background image

DocID025202 Rev 7

RM0365

Inter-integrated circuit (I2C) interface

834

28.4.8

I2C master mode

I2C master initialization

Before enabling the peripheral, the I2C master clock must be configured by setting the
SCLH and SCLL bits in the I2C_TIMINGR register.

The STM32CubeMX tool calculates and provides the I2C_TIMINGR content in the I2C
Configuration window.

A clock synchronization mechanism is implemented in order to support multi-master
environment and slave clock stretching.

In order to allow clock synchronization:

•

The low level of the clock is counted using the SCLL counter, starting from the SCL low
level internal detection.

•

The high level of the clock is counted using the SCLH counter, starting from the SCL
high level internal detection.

The I2C detects its own SCL low level after a

t

SYNC1

delay

depending on the SCL falling

edge, SCL input noise filters ( digital) and SCL synchronization to the I2CxCLK
clock. The I2C releases SCL to high level once the SCLL counter reaches the value
programmed in the SCLL[7:0] bits in the I2C_TIMINGR register.

The I2C detects its own SCL high level after a

t

SYNC2

delay depending on the SCL rising

edge, SCL input noise filters ( digital) and SCL synchronization to I2CxCLK clock.
The I2C ties SCL to low level once the SCLH counter is reached reaches the value
programmed in the SCLH[7:0] bits in the I2C_TIMINGR register.

Consequently the master clock period is:

t

SCL =

t

SYNC1

+ t

SYNC2 +

{[(SCLH+1) + (SCLL+1)] x (PRESC+1) x t

I2CCLK

}

The duration of t

SYNC1

depends on these parameters:

–

SCL falling slope

–

When enabled, input delay induced by the analog filter.

–

When enabled, input delay induced by the digital filter: DNF

x t

I2CCLK

–

Delay due to SCL synchronization with I2CCLK clock (2 to 3 I2CCLK periods)

The duration of t

SYNC2

depends on these parameters:

–

SCL rising slope

–

When enabled, input delay induced by the analog filter.

–

When enabled, input delay induced by the digital filter: DNF

x t

I2CCLK

–

Delay due to SCL synchronization with I2CCLK clock (2 to 3 I2CCLK periods)

«
...
784
785
786
787
788
...
»

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

Brand: Vanguard Pages: 4

Brand: Vivotek Pages: 136

SRCSASBB8I - RAID Controller

Brand: Intel Pages: 36

Brand: T.A Pages: 11

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Brand: Ubiquiti Pages: 13

VIGI NVR1004H-4P

Brand: TP-Link Pages: 2

Brand: Kontron Pages: 62

Brand: PADAUK Pages: 27

ARC-12x4 Series

Brand: Areca Pages: 2

PSJ-VZ58 gen3 OEM

Brand: Grizzly Pages: 12

Brand: ICP DAS USA Pages: 62

Brand: ICP DAS USA Pages: 8

Emulation Probe M306V8T-EPB

Brand: Renesas Pages: 90

System 200V Series

Brand: VIPA Pages: 76

DUAL SOCKET PC CARD CONTROLLER PCI1520 Implementation

Brand: Texas Instruments Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands