manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Embedded Flash memory

RM0365

63/1080

DocID025202 Rev 7

1.

Check that no main Flash memory operation is ongoing by checking the BSY bit in the 
FLASH_SR register.

2.  Set the PG bit in the FLASH_CR register.
3.  Perform the data write (half-word) at the desired address.
4.  Wait until the BSY bit is reset in the FLASH_SR register.
5.  Check the EOP flag in the FLASH_SR register (it is set when the programming 

operation has succeeded), and then clear it by software.

Note:

The registers are not accessible in write mode when the BSY bit of the 

FLASH_SR

 register 

is set.

Flash memory erase

The Flash memory can be erased page by page or completely (Mass Erase).

Page Erase

To erase a page, the procedure below should be followed:
1.

Check that no Flash memory operation is ongoing by checking the BSY bit in the 
FLASH_CR register.

2.  Set the PER bit in the FLASH_CR register
3.  Program the FLASH_AR register to select a page to erase
4.  Set the STRT bit in the FLASH_CR register (see below note)
5.  Wait for the BSY bit to be reset
6.  Check the EOP flag in the FLASH_SR register (it is set when the erase operation has 

succeeded), and then clear it by software.

7.  Clear the EOP flag.

Note:

The software should start checking if the BSY bit equals ‘0’ at least one CPU cycle after 
setting the STRT bit.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

dbx Zone Pro 640 Manual preview
Zone Pro 640
Brand: dbx Pages: 2
dbx 166 Quick Start Manual preview
166
Brand: dbx Pages: 17
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
Behringer EXPANSION CARD X-DANTE Quick Start Manual preview
EXPANSION CARD X-DANTE
Brand: Behringer Pages: 65
OpenVox B800P User Manual preview
B800P
Brand: OpenVox Pages: 13
Arduino ABX00061 Reference Manual preview
ABX00061
Brand: Arduino Pages: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
ebm-papst W3G710-NK67-01 Operating Instructions Manual preview
W3G710-NK67-01
Brand: ebm-papst Pages: 13
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
XtendLan XL-IPM401 User Manual preview
XL-IPM401
Brand: XtendLan Pages: 21
Ariesys AMK Series User'S Reference Manual preview
AMK Series
Brand: Ariesys Pages: 10
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
Harman BSS DCP-555 Installation Manual preview
BSS DCP-555
Brand: Harman Pages: 24
ADTRAN DUAL Nx56/64 1200142L1# User Manual preview
DUAL Nx56/64 1200142L1#
Brand: ADTRAN Pages: 48
VIA Technologies LPC-01 Quick Manual preview
LPC-01
Brand: VIA Technologies Pages: 2
Serial Cables PCI-AD-x16HE-BG4 User Manual preview
PCI-AD-x16HE-BG4
Brand: Serial Cables Pages: 18

Brands by name

Popular brands

Load more brands