manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

62/1080

RM0365

Embedded Flash memory

80

Figure 4. Programming procedure

The Flash memory interface preliminarily reads the value at the addressed main Flash 
memory location and checks that it has been erased. If not, the program operation is 
skipped and a warning is issued by the PGERR bit in FLASH_SR register (the only 
exception to this is when 0x0000 is programmed. In this case, the location is correctly 
programmed to 0x0000 and the PGERR bit is not set). If the addressed main Flash memory 
location is write-protected by the FLASH_WRPR register, the program operation is skipped 
and a warning is issued by the WRPRTERR bit in the FLASH_SR register. The end of the 
program operation is indicated by the EOP bit in the FLASH_SR register.

The main Flash memory programming sequence in standard mode is as follows:

5HDG)/$6+B&5B/2&.

)/$6+B&5B/2&.

 

<HV

1R

<HV

1R

3HUIRUPXQORFNVHTXHQF\

:ULWH)/$6+B&5B3*WR

3HUIRUPKDOIZRUGZULWHDWWKH

GHVLUHGDGGUHVV

)/$6+B65B%6<

 

&KHFNWKHSURJUDPPHGYDOXH

E\UHDGLQJWKHSURJUDPPHG

DGGUHVV

DLE

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
dbx ProVocal Specifications preview
ProVocal
Brand: dbx Pages: 2
Intel NetStructure ZT 5515 Product Specification preview
NetStructure ZT 5515
Brand: Intel Pages: 90
OpenVox B800P User Manual preview
B800P
Brand: OpenVox Pages: 13
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Brand: Advantech Pages: 96
Acromag ACPS3320 User Manual preview
ACPS3320
Brand: Acromag Pages: 35
CyberResearch CPBF PMX-233 User Manual preview
CPBF PMX-233
Brand: CyberResearch Pages: 59
ADLINK Technology VPX3000 Series Manual preview
VPX3000 Series
Brand: ADLINK Technology Pages: 95
ADLINK Technology aTCA-9710 User Manual preview
aTCA-9710
Brand: ADLINK Technology Pages: 86
FOLSOM Blend PRO BP-2002 Installation And Operator'S Manual preview
Blend PRO BP-2002
Brand: FOLSOM Pages: 89
Quatech SSPX-100 User Manual preview
SSPX-100
Brand: Quatech Pages: 5
ZALMAN CNPS9800 MAX User Manual preview
CNPS9800 MAX
Brand: ZALMAN Pages: 32
Clare Controls ClareVision CV-M161620-04 Installation Manual preview
ClareVision CV-M161620-04
Brand: Clare Controls Pages: 32
IBASE Technology 11th Gen Intel Core U-Series User Manual preview
11th Gen Intel Core U-Series
Brand: IBASE Technology Pages: 70
Azoteq IQ Switch ProxSense RS100 Application Notes preview
IQ Switch ProxSense RS100
Brand: Azoteq Pages: 9
Hama 00062773 Quick Manual preview
00062773
Brand: Hama Pages: 10
Intel P4000CR Installation Instructions Manual preview
P4000CR
Brand: Intel Pages: 11

Brands by name

Popular brands

Load more brands