manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Analog-to-digital converters (ADC)

RM0365

379/1080

DocID025202 Rev 7

Bits 7:6

JEXTEN[1:0]

: External Trigger Enable and Polarity Selection for injected channels

These bits are set and cleared by software to select the external trigger polarity and enable the 
trigger of an injected group. 

00: Hardware trigger detection disabled (conversions can be launched by software)
01: Hardware trigger detection on the rising edge
10: Hardware trigger detection on the falling edge
11: Hardware trigger detection on both the rising and falling edges

Note: Software is allowed to write these bits at any time, once the ADC is enabled (ADEN=1).
Note: If JQM=1 and if the Queue of Context becomes empty, the software and hardware 

triggers of the injected sequence are both internally disabled (refer to 

Section 15.3.21: 

Queue of context for injected conversions

)

Bits 5:2

JEXTSEL[3:0]

: External Trigger Selection for injected group

These bits select the external event used to trigger the start of conversion of an injected group:

0000: Event 0
0001: Event 1
0010: Event 2
0011: Event 3
0100: Event 4
0101: Event 5
0110: Event 6
0111: Event 7
...
1111: Event 15

Note: Software is allowed to write these bits at any time, once the ADC is enabled (ADEN=1).

Bits 1:0

JL[1:0]:

 Injected channel sequence length

These bits are written by software to define the total number of conversions in the injected 
channel conversion sequence.

00: 1 conversion
01: 2 conversions
10: 3 conversions
11: 4 conversions

Note: Software is allowed to write these bits at any time, once the ADC is enabled (ADEN=1).

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Alesis QUADRAVERB Reference Manual preview
QUADRAVERB
Brand: Alesis Pages: 61
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
National Instruments NI-9206 Getting Started preview
NI-9206
Brand: National Instruments Pages: 8
ZALMAN Extreme Gaming VGA Cooler GV1000 User Manual preview
Extreme Gaming VGA Cooler GV1000
Brand: ZALMAN Pages: 7
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Brand: NKE Pages: 15
C-Smartlink DMH25 Manual preview
DMH25
Brand: C-Smartlink Pages: 7
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Brand: ZALMAN Pages: 18
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
Renesas PROM Programming Adapters PCA7438F-64A User Manual preview
PROM Programming Adapters PCA7438F-64A
Brand: Renesas Pages: 18
StetSom STX2448 User Manual preview
STX2448
Brand: StetSom Pages: 18
ZALMAN ZM-RWB1 User Manual preview
ZM-RWB1
Brand: ZALMAN Pages: 6
Garland EdgeSafe M40G1AC User Manual preview
EdgeSafe M40G1AC
Brand: Garland Pages: 159

Brands by name

Popular brands

Load more brands