manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

General-purpose timers (TIM15/TIM16/TIM17)

RM0365

675/1080

DocID025202 Rev 7

22.6 TIM16/TIM17 

registers

Refer to 

Section 2.1 on page 42

 for a list of abbreviations used in register descriptions. 

22.6.1 TIM16/TIM17 

control register 1 (TIMx_CR1)

Address offset: 0x00

Reset value: 0x0000

         

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Res

Res

Res

Res

UIF 

REM-

AP

Res

CKD[1:0]

ARPE

Res

Res

Res

OPM

URS

UDIS

CEN

rw

rw

rw

rw

rw

rw

rw

rw

Bits 15:12 Reserved, must be kept at reset value.

Bit 11

UIFREMAP

: UIF status bit remapping

0: No remapping. UIF status bit is not copied to TIMx_CNT register bit 31.
1: Remapping enabled. UIF status bit is copied to TIMx_CNT register bit 31.

Bit 10 Reserved, must be kept at reset value.

Bits 9:8

CKD[1:0]

: Clock division

This bit-field indicates the division ratio between the timer clock (CK_INT) frequency and the 
dead-time and sampling clock (t

DTS

)used by the dead-time generators and the digital filters 

(TIx),
00: t

DTS

=t

CK_INT

01: t

DTS

=2*t

CK_INT

10: t

DTS

=4*t

CK_INT

11: Reserved, do not program this value

Bit 7

ARPE

: Auto-reload preload enable

0: TIMx_ARR register is not buffered
1: TIMx_ARR register is buffered

Bits 6:4 Reserved, must be kept at reset value.

Bit 3

OPM

: One pulse mode

0: Counter is not stopped at update event
1: Counter stops counting at the next update event (clearing the bit CEN)

Bit 2

URS

:

 

Update request source

This bit is set and cleared by software to select the UEV event sources.
0: Any of the following events generate an update interrupt or DMA request if enabled. 
These events can be: 

–

Counter overflow/underflow

–

Setting the UG bit

–

Update generation through the slave mode controller

1: Only counter overflow/underflow generates an update interrupt or DMA request if 
enabled.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

hilscher CIFX 104 User Manual preview
CIFX 104
Brand: hilscher Pages: 154
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Brand: Ubiquiti Pages: 23
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Brand: Intel Pages: 105
Antec KÜHLER H2O 920 Software Manual preview
KÜHLER H2O 920
Brand: Antec Pages: 6
Knowles IA611 Xplained Pro User Manual preview
IA611 Xplained Pro
Brand: Knowles Pages: 14
Corsair ELITE LCD UPGRADE KIT Manual preview
ELITE LCD UPGRADE KIT
Brand: Corsair Pages: 11
Ross ULTRIX-FM-NS-1RU Install Manual preview
ULTRIX-FM-NS-1RU
Brand: Ross Pages: 5
Jetter JVM-507B - HMI Installation Manual preview
JVM-507B - HMI
Brand: Jetter Pages: 20
Intellinet 560665 User Manual preview
560665
Brand: Intellinet Pages: 32
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Brand: Kontron Pages: 20
ESD C.2044.04 Hardware Manual preview
C.2044.04
Brand: ESD Pages: 30
iTON ID6ZFN-BK0 User Manual preview
ID6ZFN-BK0
Brand: iTON Pages: 12
ebm-papst 8314/2H Operating Manual preview
8314/2H
Brand: ebm-papst Pages: 6
ebm-papst D3G160-BD05-02 Operating Instructions Manual preview
D3G160-BD05-02
Brand: ebm-papst Pages: 12
Costar CR6420XDi Quick Manual preview
CR6420XDi
Brand: Costar Pages: 14
Extron electronics Network Device PIP 444 Specification Sheet preview
Network Device PIP 444
Brand: Extron electronics Pages: 2

Brands by name

Popular brands

Load more brands