manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

146/1080

RM0365

Reset and clock control (RCC)

154

Bit 29

IWDGRSTF:

 Independent window watchdog reset flag

Set by hardware when an independent watchdog reset from V

DD

 domain occurs. Cleared by 

writing to the RMVF bit.

0: No watchdog reset occurred
1: Watchdog reset occurred

Bit 28

SFTRSTF:

 Software reset flag

Set by hardware when a software reset occurs. Cleared by writing to the RMVF bit.

0: No software reset occurred
1: Software reset occurred

Bit 27

PORRSTF:

 POR/PDR flag

Set by hardware when a POR/PDR occurs. Cleared by writing to the RMVF bit.

0: No POR/PDR occurred
1: POR/PDR occurred

Bit 26

PINRSTF:

 PIN reset flag

Set by hardware when a reset from the NRST pin occurs. Cleared by writing to the RMVF bit.

0: No reset from NRST pin occurred
1: Reset from NRST pin occurred

Bit 25

OBLRSTF:

 Option byte loader reset flag

Set by hardware when a reset from the OBL occurs. Cleared by writing to the RMVF bit.

0: No reset from OBL occurred
1: Reset from OBL occurred

Bit 24

RMVF:

 Remove reset flag

Set by software to clear the reset flags.

0: No effect
1: Clear the reset flags

Bit 23

V18PWRRSTF

: Reset flag of the 1.8 V domain. 

Set by hardware when a POR/PDR of the 1.8 V domain occurred. Cleared by writing to the 
RMVF bit. 

0: No POR/PDR reset of the 1.8 V domain occurred 
1: POR/PDR reset of the 1.8 V domain occurred 

Note:

On the STM32F3x8 products, this flag is reserved.

Bits 22:2 Reserved, must be kept at reset value.

Bit 1

LSIRDY:

 LSI oscillator ready

Set and cleared by hardware to indicate when the LSI oscillator is stable. After the LSION bit is 
cleared, LSIRDY goes low after 3 LSI oscillator clock cycles.

0: LSI oscillator not ready
1: LSI oscillator ready

Bit 0

LSION:

 LSI oscillator enable

Set and cleared by software.

0: LSI oscillator OFF
1: LSI oscillator ON

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Ubiquiti M900 Quick Start Manual preview
M900
Brand: Ubiquiti Pages: 24
3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
D-Link ShareCenter Quattro DNS-345 Quick Install Manual preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 40
D-Link ShareCenter Quattro DNS-345 Datasheet preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 4
D-Link MYDLINK DNR-322L Datasheet preview
MYDLINK DNR-322L
Brand: D-Link Pages: 4
D-Link mydlink DNR-312L Quick Install Manual preview
mydlink DNR-312L
Brand: D-Link Pages: 8
D-Link DNS-722-4 Quick Install Manual preview
DNS-722-4
Brand: D-Link Pages: 16
D-Link DNS-722-4 User Manual preview
DNS-722-4
Brand: D-Link Pages: 88
Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
Observint NVR4 Firmware User Manual preview
NVR4
Brand: Observint Pages: 117
F5 i5000 Series Platform Manual preview
i5000 Series
Brand: F5 Pages: 72
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
Point of View SmartTV 210 User Manual preview
SmartTV 210
Brand: Point of View Pages: 13
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
MF DIGITAL 5200 Live Series EventCD Operator'S Manual preview
5200 Live Series EventCD
Brand: MF DIGITAL Pages: 21
Loopcomm LP-8014 Quick Start Manual preview
LP-8014
Brand: Loopcomm Pages: 2
Eagle Technology PC104PLUS-26 User Manual preview
PC104PLUS-26
Brand: Eagle Technology Pages: 39

Brands by name

Popular brands

Load more brands