STMicroelectronics RM0365 Reference Manual Download Page 1032 | Manualshive

Page: 1032 / 1080

background image

DocID025202 Rev 7

RM0365

Universal serial bus full-speed device interface (USB)

1036

Address offset (“2 x 16 bits/word” access scheme): [USB_BTABLE] + n*8 + 2

USB local address: [USB_BTABLE] + n*8 + 2

Note:

In case of double-buffered or isochronous endpoints in the IN direction, this address location
is referred to as USB_COUNTn_TX_0.
In case of double-buffered or isochronous endpoints in the OUT direction, this address
location is used for USB_COUNTn_RX_0.

Reception buffer address n (USB_ADDRn_RX)

Address offset (“1 x 16 bits/word” access scheme): [USB_BTABLE] + n*16 + 8

Address offset (“2 x 16 bits/word” access scheme): [USB_BTABLE] + n*8 + 4

USB local address: [USB_BTABLE] + n*8 + 4

Note:

In case of double-buffered or isochronous endpoints in the OUT direction, this address
location is referred to as USB_ADDRn_RX_1.
In case of double-buffered or isochronous endpoints in the IN direction, this address location
is used for USB_ADDRn_TX_1.

Reception byte count n (USB_COUNTn_RX)

Address offset (“1 x 16 bits/word” access scheme): [USB_BTABLE] + n*16 + 12

Address offset (“2 x 16 bits/word” access scheme): [USB_BTABLE] + n*8 + 6

USB local address: [USB_BTABLE] + n*8 + 6

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Res.

Res.

Res.

Res.

Res.

Res.

COUNTn_TX[9:0]

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

Bits 15:10 These bits are not used since packet size is limited by USB specifications to 1023 bytes. Their

value is not considered by the USB peripheral.

Bits 9:0

COUNTn_TX[9:0]:

Transmission byte count

These bits contain the number of bytes to be transmitted by the endpoint associated with the
USB_EPnR register at the next IN token addressed to it.

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

ADDRn_RX[15:1]

-

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

-

Bits 15:1

ADDRn_RX[15:1]:

Reception buffer address

These bits point to the starting address of the packet buffer, which will contain the data
received by the endpoint associated with the USB_EPnR register at the next OUT/SETUP
token addressed to it.

Bit 0 This bit must always be written as ‘0 since packet memory is half-word wide and all packet

buffers must be half-word aligned.

«
...
1030
1031
1032
1033
1034
...
»

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Brand: GE Pages: 6

Enterprise Filter Authentication R3000

Brand: 8e6 Technologies Pages: 66

Brand: Paradyne Pages: 11

Brand: Paradyne Pages: 19

COMSPHERE 3550 Series

Brand: Paradyne Pages: 153

Jetstream CPX-1000

Brand: Paradyne Pages: 141

Brand: IBM Pages: 63

Brand: ETAS Pages: 69

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

APS6-400 Series

Brand: Eaton Pages: 114

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: FONESTAR Pages: 8

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

NIC-FC730i-Mb-2-32G

Brand: H3C Pages: 37

Brand: WABCO Pages: 29

Brand: ACTi Pages: 12

Brand: C&T Solution Pages: 129

Brand: HighPoint Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands