manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

124/1080

RM0365

Reset and clock control (RCC)

154

In this configuration:

•

On the STM32F302xB/C, AHB and APB2 prescalers are set to 1, i.e. AHB and APB2 
clocks are not divided with respect to the system clock.

•

On the STM32F302x6/8 AHB or APB2 subsystem clocks are not divided by more than 
2 cumulatively with respect to the system clock.

9.2.11 Watchdog 

clock

If the Independent watchdog (IWDG) is started by either hardware option or software 
access, the LSI oscillator is forced ON and cannot be disabled. After the LSI oscillator 
temporization, the clock is provided to the IWDG.

9.2.12 I2S 

clock 

The I2S clock can be either the System clock or an external clock provided on I2S_CKIN 
pin. The selection of the I2S clock source is performed using bit 23 (I2SSRC) of 
RCC_CFGR register.

9.2.13 Clock-out 

capability

The microcontroller clock output (MCO) capability allows the clock to be output onto the 
external MCO pin. The configuration registers of the corresponding GPIO port must be 
programmed in alternate function mode. One of 5 clock signals can be selected as the MCO 
clock. 

•

LSI

•

LSE

•

SYSCLK

•

HSI

•

HSE

•

PLL clock dividedby 2 on the STM32F302xBxC and PLL clock not divided or divided by 
2 on the STM32F302x6/8 and STM32F302xD/E, using the PLLNODIV bit in 
RCC_CFGR register

The selection is controlled by the MCO[2:0] bits in the 

Clock configuration register 

(RCC_CFGR)

. 

On the STM32F302x6/8 and STM32F302xD/E, the MCO frequency can be reduced by a 
configurable divider, controlled by the MCOPRE[2..0] bits of the Clock configuration register 
(RCC_CFGR).

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Patton electronics 1090 Service Manual preview
1090
Brand: Patton electronics Pages: 8
X-Micro XWL-11GPRG Quick Start Manual preview
XWL-11GPRG
Brand: X-Micro Pages: 9
X-Micro XWL-11GPAG Quick Installation Manual preview
XWL-11GPAG
Brand: X-Micro Pages: 19
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
NEC N8141-75F Startup Manual preview
N8141-75F
Brand: NEC Pages: 6
Industrex M43ic Instruction Manual preview
M43ic
Brand: Industrex Pages: 51
Thermalright AXP-100H MUSCLE Manual preview
AXP-100H MUSCLE
Brand: Thermalright Pages: 36
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
Aaeon SBC-555 Manual preview
SBC-555
Brand: Aaeon Pages: 72
Kontron ePanel-C3 Technical Manual preview
ePanel-C3
Brand: Kontron Pages: 62
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Brand: Ista Pages: 16
National Instruments IMAQTM User Manual preview
IMAQTM
Brand: National Instruments Pages: 121
Smacq Technologies PCI-1232 User Manual preview
PCI-1232
Brand: Smacq Technologies Pages: 22
Cypress Semiconductor CY7C1410JV18 Specification Sheet preview
CY7C1410JV18
Brand: Cypress Semiconductor Pages: 26
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Brand: ZALMAN Pages: 9
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Brand: PairGain Pages: 48

Brands by name

Popular brands

Load more brands