manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Analog-to-digital converters (ADC)

RM0365

367/1080

DocID025202 Rev 7

15.5.5 

ADC sample time register 1 (ADCx_SMPR1, x=1

..

2)

Address offset: 0x14

Reset value: 0x0000 0000

         

Bit 2 Reserved, must be kept at reset value.

Bit 1

DMACFG

: Direct memory access configuration

This bit is set and cleared by software to select between two DMA modes of operation and is effective 
only when DMAEN=1.

0: DMA One Shot Mode selected
1: DMA Circular Mode selected
For more details, refer to 

Section : Managing conversions using the DMA

Note: Software is allowed to write this bit only when ADSTART=0 and JADSTART=0 (which ensures 

that no conversion is ongoing).

Note: In dual-ADC modes, this bit is not relevant and replaced by control bit DMACFG of the 

ADCx_CCR register.

Bit 0

DMAEN

: Direct memory access enable

This bit is set and cleared by software to enable the generation of DMA requests. This allows to use 
the GP-DMA to manage automatically the converted data. For more details, refer to 

Section : 

Managing conversions using the DMA

.

0: DMA disabled
1: DMA enabled

Note: Software is allowed to write this bit only when ADSTART=0 and JADSTART=0 (which ensures 

that no conversion is ongoing).

Note: In dual-ADC modes, this bit is not relevant and replaced by control bits MDMA[1:0] of the 

ADCx_CCR register.

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Res.

Res.

SMP9[2:0]

SMP8[2:0]

SMP7[2:0]

SMP6[2:0]

SMP5[2:1]

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

SMP

5_0

SMP4[2:0]

SMP3[2:0]

SMP2[2:0]

SMP1[2:0]

Res.

Res.

Res.

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

D-Link DES-1210-08P Manual preview
DES-1210-08P
Brand: D-Link Pages: 15
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Brand: JUMO Pages: 41
Quantum QWCM Installation Manual preview
QWCM
Brand: Quantum Pages: 7
ARTERY AT32F421 Series Reference Manual preview
AT32F421 Series
Brand: ARTERY Pages: 337
Airlink101 AWMB100 User Manual preview
AWMB100
Brand: Airlink101 Pages: 46
S&T TPMS1209T02-ER User Manual preview
TPMS1209T02-ER
Brand: S&T Pages: 28
ICP Chapter C Quick Setup Manual preview
Chapter C
Brand: ICP Pages: 68
EZCast Pro Dongle II User Manual preview
Pro Dongle II
Brand: EZCast Pages: 24
Z-Wave IOMOD10F Hardware User Manual preview
IOMOD10F
Brand: Z-Wave Pages: 42
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Brand: Taiwan Commate Computer Inc. Pages: 25
Greenlee 910FS Instruction Manual preview
910FS
Brand: Greenlee Pages: 52
Renesas R0E424270CFLE0 User Manual preview
R0E424270CFLE0
Brand: Renesas Pages: 4
IBM TSO/E REXX User Manual preview
TSO/E REXX
Brand: IBM Pages: 242
WiebeTech FCDKV4 User Manual preview
FCDKV4
Brand: WiebeTech Pages: 8
Paradyne JetFusion 2004 User Manual preview
JetFusion 2004
Brand: Paradyne Pages: 216
Planet FGSW-4840S User Manual preview
FGSW-4840S
Brand: Planet Pages: 38
Domburg Switch Polarization Print HPP4 Quick Start Manual preview
Switch Polarization Print HPP4
Brand: Domburg Pages: 11
MikroTik RBM11G Quick Start Manual preview
RBM11G
Brand: MikroTik Pages: 4

Brands by name

Popular brands

Load more brands