manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Analog-to-digital converters (ADC)

RM0365

357/1080

DocID025202 Rev 7

         

Bit 5

JEOC:

 Injected channel end of conversion flag

This bit is set by hardware at the end of each injected conversion of a channel when a new data is 
available in the corresponding ADCx_JDRy register. It is cleared by software writing 1 to it or by 
reading the corresponding ADCx_JDRy register

0: Injected channel conversion not complete (or the flag event was already acknowledged and 
cleared by software)
1: Injected channel conversion complete

Bit 4

OVR

: ADC overrun

This bit is set by hardware when an overrun occurs on a regular channel, meaning that a new 
conversion has completed while the EOC flag was already set. It is cleared by software writing 1 to it.

0: No overrun occurred (or the flag event was already acknowledged and cleared by software)
1: Overrun has occurred

Bit 3

EOS

: End of regular sequence flag

This bit is set by hardware at the end of the conversions of a regular sequence of channels. It is 
cleared by software writing 1 to it.

0: Regular Conversions sequence not complete (or the flag event was already acknowledged and 
cleared by software)
1: Regular Conversions sequence complete

Bit 2

EOC

: End of conversion flag

This bit is set by hardware at the end of each regular conversion of a channel when a new data is 
available in the ADCx_DR register. It is cleared by software writing 1 to it or by reading the ADCx_DR 
register

0: Regular channel conversion not complete (or the flag event was already acknowledged and 
cleared by software)
1: Regular channel conversion complete

Bit 1

EOSMP

: End of sampling flag

This bit is set by hardware during the conversion of any channel (only for regular channels), at the end 
of the sampling phase.

0: not at the end of the sampling phase (or the flag event was already acknowledged and cleared by 
software)
1: End of sampling phase reached

Bit 0

ADRDY

: ADC ready 

This bit is set by hardware after the ADC has been enabled (bit ADEN=1) and when the ADC reaches 
a state where it is ready to accept conversion requests.
It is cleared by software writing 1 to it.

0: ADC not yet ready to start conversion (or the flag event was already acknowledged and cleared 
by software)
1: ADC is ready to start conversion

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Brand: 8e6 Technologies Pages: 74
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
Barco Encore VPx Installation Manual preview
Encore VPx
Brand: Barco Pages: 30
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Brand: Sans Digital Pages: 9
MA lighting 8Port Node Quick Manual preview
8Port Node
Brand: MA lighting Pages: 49
Hanwha Techwin Wisenet XRN-6410RB2-24TB User Manual preview
Wisenet XRN-6410RB2-24TB
Brand: Hanwha Techwin Pages: 124
Sony Ericsson Developer's Board Manual preview
Developer's Board
Brand: Sony Ericsson Pages: 28
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Brand: Ciara Pages: 14
Jetter JVM-507B - HMI Installation Manual preview
JVM-507B - HMI
Brand: Jetter Pages: 20
Lucent Technologies CIB40 Installation Manual preview
CIB40
Brand: Lucent Technologies Pages: 7
FOLSOM Blend PRO BP-2002 Installation And Operator'S Manual preview
Blend PRO BP-2002
Brand: FOLSOM Pages: 89
Parker Sporlan Division SCS-PB Series Installation And Operating Instructions Manual preview
Sporlan Division SCS-PB Series
Brand: Parker Pages: 10

Brands by name

Popular brands

Load more brands