manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

106/1080

RM0365

Power control (PWR)

112

         

8.3.5 Standby 

mode

The Standby mode allows to achieve the lowest power consumption. It is based on the 
ARM

®

 Cortex

®

-M4 deepsleep mode, with the voltage regulator disabled. The 1.8 V domain 

is consequently powered off. The PLL, the HSI oscillator and the HSE oscillator are also 
switched off. SRAM and register contents are lost except for registers in the RTC domain 
and Standby circuitry (see 

Figure 8

).

Entering Standby mode

Refer to 

Table 27

 for more details on how to enter Standby mode.

In Standby mode, the following features can be selected by programming individual control 
bits:

•

Independent watchdog (IWDG): the IWDG is started by writing to its Key register or by 
hardware option. Once started it cannot be stopped except by a reset. See 

Table 26. Stop mode

Stop mode

Description

Mode entry

WFI (Wait for Interrupt) or WFE (Wait for Event) while:
– Set SLEEPDEEP bit in ARM

®

 Cortex

®

-M4 System Control register

– Clear PDDS bit in Power Control register (PWR_CR)
– Select the voltage regulator mode by configuring LPDS bit in PWR_CR

Note:

 To enter Stop mode, all EXTI Line pending bits (in 

Pending register 

(EXTI_PR1)

), all peripherals interrupt pending bits and RTC Alarm flag 

must be reset. Otherwise, the Stop mode entry procedure is ignored and 
program execution continues. 
If the application needs to disable the external oscillator (external clock) 
before entering Stop mode, the system clock source must be first switched 
to HSI and then clear the HSEON bit.
Otherwise, if before entering Stop mode the HSEON bit is kept at 1, the 
security system (CSS) feature must be enabled to detect any external 
oscillator (external clock) failure and avoid a malfunction when entering 
Stop mode.

Mode exit

If WFI was used for entry:
– Any EXTI Line configured in Interrupt mode (the corresponding EXTI 

Interrupt vector must be enabled in the NVIC).

– Some specific communication peripherals (USART, I2C) interrupts, when 

programmed in wakeup mode (the peripheral must be programmed in 
wakeup mode and the corresponding interrupt vector must be enabled in 
the NVIC). 

Refer to 

Table 40: STM32F302xB/C/D/E vector table

 and 

Table 41: 

STM32F302x6/8 vector table

.

If WFE was used for entry:

Any EXTI Line configured in event mode. Refer to 

Section 13.2.3: 

Wakeup event management on page 213

Wakeup latency

HSI RC wakeup time + regulator wakeup time from Low-power mode

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
HighPoint SSD7540L Quick Installation Manual preview
SSD7540L
Brand: HighPoint Pages: 10
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
Aerotech QNP3 Series Hardware Manual preview
QNP3 Series
Brand: Aerotech Pages: 62
ZALMAN OPTIMA II CNPS10X User Manual preview
OPTIMA II CNPS10X
Brand: ZALMAN Pages: 20
PairGain T1L2F10A Manual preview
T1L2F10A
Brand: PairGain Pages: 76
Lattice Semiconductor mVision AR0234 User Manual preview
mVision AR0234
Brand: Lattice Semiconductor Pages: 25
Kodak X-Omat 1000 Service Manual preview
X-Omat 1000
Brand: Kodak Pages: 86
New Media Technology IP Power 9212 User Manual preview
IP Power 9212
Brand: New Media Technology Pages: 26
DataDirect Networks EF2915 Series User Manual preview
EF2915 Series
Brand: DataDirect Networks Pages: 97
Johnson Controls TR-9100-8001 Configuration Manual preview
TR-9100-8001
Brand: Johnson Controls Pages: 40

Brands by name

Popular brands

Load more brands