STMicroelectronics RM0365 Reference Manual Download Page 205 | Manualshive

Page: 205 / 1080

background image

Interrupts and events

RM0365

DocID025202 Rev 7

13

Interrupts and events

13.1

Nested vectored interrupt controller (NVIC)

13.1.1

NVIC main features

•

66 maskable interrupt channels (not including the sixteen Cortex

®

-M4 with FPU

interrupt lines)

•

16 programmable priority levels (4 bits of interrupt priority are used)

•

Low-latency exception and interrupt handling

•

Power management control

•

Implementation of System Control Registers

The NVIC and the processor core interface are closely coupled, which enables low latency
interrupt processing and efficient processing of late arriving interrupts.

All interrupts including the core exceptions are managed by the NVIC. For more information
on exceptions and NVIC programming, refer to the PM0214 programming manual for
Cortex

®

-M4 products.

13.1.2 SysTick

calibration value register

The SysTick calibration value is set to 9000, which gives a reference time base of 1 ms with
the SysTick clock set to 9 MHz (max f

HCLK

/8).

13.1.3

Interrupt and exception vectors

is the vector table for STM32F302xB/C devices.

is the vector table for

STM32F302x6/8 devices.

Table 40. STM32F302xB/C/D/E vector table

Position

Priority

Type of
priority

Acronym

Description

Address

-

-

-

-

Reserved

0x0000 0000

-

-3

fixed

Reset

Reset

0x0000 0004

-

-2

fixed

NMI

Non maskable interrupt. The RCC Clock
Security System (CSS) is linked to the NMI
vector.

0x0000 0008

-

-1

fixed

HardFault

All class of fault

0x0000 000C

-

0

settable

MemManage

Memory management

0x0000 0010

-

1

settable

BusFault

Pre-fetch fault, memory access fault

0x0000 0014

-

2

settable

UsageFault

Undefined instruction or illegal state

0x0000 0018

-

-

-

-

Reserved

0x0000 001C -

0x0000 0028

«
...
203
204
205
206
207
...
»

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

All in One Printer

Brand: Baracoda Pages: 42

FrameSaver 9120

Brand: Paradyne Pages: 2

Brand: Harmonic Pages: 56

Brand: Maxim Pages: 26

Brand: red lion Pages: 5

Brand: Cameo Pages: 23

Brand: Caen Pages: 14

Brand: SeaLevel Pages: 34

Powereta iQP Series

Brand: TDK Pages: 2

MS-96 Vial Reader

Brand: Microscan Pages: 67

Brand: LST Pages: 1

Brand: Avigilon Pages: 12

ENHANCED PSD 239 H2R

Brand: ADTRAN Pages: 2

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Brand: MACHINIST Pages: 15

Brand: peplink Pages: 111

Cascade Express

Brand: Riverbed Pages: 92

Brand: Exsys Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands