manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Inter-integrated circuit (I2C) interface

RM0365

831/1080

DocID025202 Rev 7

28.7.9 

PEC register (I2C_PECR)

Address offset: 0x20

Reset value: 0x0000 0000

Access: No wait states

         

         

Note:

If the SMBus feature is not supported, this register is reserved and forced by hardware to 
“0x00000000”. Please refer to 

Section 28.3: I2C implementation

.

Bit 9

ARLOCF

:

 

Arbitration Lost flag clear

Writing 1 to this bit clears the ARLO flag in the I2C_ISR register.

Bit 8

BERRCF

: Bus error flag clear

Writing 1 to this bit clears the BERRF flag in the I2C_ISR register.

Bits 7:6 Reserved, must be kept at reset value.

Bit 5

STOPCF

: Stop detection flag clear 

Writing 1 to this bit clears the STOPF flag in the I2C_ISR register.

Bit 4

NACKCF

:

 

Not Acknowledge flag clear

Writing 1 to this bit clears the ACKF flag in I2C_ISR register.

Bit 3

ADDRCF

:

 

Address matched flag clear 

Writing 1 to this bit clears the ADDR flag in the I2C_ISR register. Writing 1 to this bit also clears 
the START bit in the I2C_CR2 register.

Bits 2:0 Reserved, must be kept at reset value.

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

PEC[7:0]

r

Bits 31:8 Reserved, must be kept at reset value.

Bits 7:0

PEC[7:0]

 Packet error checking register

This field contains the internal PEC when PECEN=1.
The PEC is cleared by hardware when PE=0.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Brand: Data Translation Pages: 60
T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
SeaLevel 7205e User Manual preview
7205e
Brand: SeaLevel Pages: 34
Medel RONDO 3 Quick Manual preview
RONDO 3
Brand: Medel Pages: 28
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
Zonet ZEN3320E Quick Installation Manual preview
ZEN3320E
Brand: Zonet Pages: 1
SIIG US2273 Quick Installation Manual preview
US2273
Brand: SIIG Pages: 8
Mod Duo X User Manual preview
Duo X
Brand: Mod Pages: 11
Galileo Quark SoC X1000 Getting Started Manual preview
Quark SoC X1000
Brand: Galileo Pages: 20
ATEN Altusen SN0100 Series User Manual preview
Altusen SN0100 Series
Brand: ATEN Pages: 178
Paradyne SLV Installation Instructions Manual preview
SLV
Brand: Paradyne Pages: 28
Boser HS-2621 Manual preview
HS-2621
Brand: Boser Pages: 54
Planet FGSW-4840S User Manual preview
FGSW-4840S
Brand: Planet Pages: 38
ebm-papst 8314/2H Operating Manual preview
8314/2H
Brand: ebm-papst Pages: 6
ebm-papst D3G160-BD05-02 Operating Instructions Manual preview
D3G160-BD05-02
Brand: ebm-papst Pages: 12
ADF Web AXIS HD67555 User Manual preview
AXIS HD67555
Brand: ADF Web Pages: 20

Brands by name

Popular brands

Load more brands