manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

1058/1080

RM0365

Debug support (DBG)

1066

33.14.5  Debug MCU APB2 freeze register (DBGMCU_APB2_FZ)

The DBGMCU_APB2_FZ register is used to configure the MCU under DEBUG. It concerns 
APB2 peripherals:

•

Timer clock counter freeze

This register is mapped on the external PPB bus at address 0xE004 200C

It is asynchronously reset by the POR (and not the system reset). It can be written by the 
debugger under system reset.

Address: 0xE004 200C

Only 32-bit access is supported.

POR: 0x0000 0000 (not reset by system reset)

         

         

33.15 

TPIU (trace port interface unit)

33.15.1 Introduction

The TPIU acts as a bridge between the on-chip trace data from the ITM and the ETM.

The output data stream encapsulates the trace source ID, that is then captured by a 

trace 

port analyzer 

(TPA).

The core embeds a simple TPIU, especially designed for low-cost debug (consisting of a 
special version of the CoreSight TPIU).

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res

Res.

DBG

_

TIM1

7_ST

O

P

DBG

_

TIM1

6_ST

O

P

DBG

_

TIM1

5_ST

O

P

Res

DBG_

T

IM1_S

T

O

P

rw

rw

rw

rw

rw

Bits 31:5 Reserved, must be kept at reset value.

Bits 4:0

DBG_TIMx_STOP:

 TIMx counter stopped when core is halted (x=1, 8,15..17)

0: The clock of the involved timer counter is fed even if the core is halted
1: The clock of the involved timer counter is stopped and the outputs are disabled when the 
core is halted

Note: Bit1 and Bit 5 are reserved.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

dbx ProVocal Specifications preview
ProVocal
Brand: dbx Pages: 2
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Brand: National Instruments Pages: 85
Octavo OSD3358-SM-RED Getting Started Manual preview
OSD3358-SM-RED
Brand: Octavo Pages: 28
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Brand: B&B Electronics Pages: 16
hilscher CIFX 104 User Manual preview
CIFX 104
Brand: hilscher Pages: 154
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
Dataprobe iBoot-Exp Manual preview
iBoot-Exp
Brand: Dataprobe Pages: 5
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
Cypress PSoC 4 S Series Quick Start Manual preview
PSoC 4 S Series
Brand: Cypress Pages: 4
Idis DR-1500 Series Quick Manual preview
DR-1500 Series
Brand: Idis Pages: 17
ICP DAS USA VEX-112 Quick Start Manual preview
VEX-112
Brand: ICP DAS USA Pages: 8
Valcom VIP-997 Manual preview
VIP-997
Brand: Valcom Pages: 4
SonicWALL Internet Security Appliances Administrator'S Manual preview
Internet Security Appliances
Brand: SonicWALL Pages: 293
netsys NH-310S User Manual preview
NH-310S
Brand: netsys Pages: 38
Dvico FusionHDTV 5 GOLD User Manual preview
FusionHDTV 5 GOLD
Brand: Dvico Pages: 64

Brands by name

Popular brands

Load more brands