manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

984/1080

RM0365

Controller area network (bxCAN)

CAN receive FIFO 0 register (CAN_RF0R)

Address offset: 0x0C
Reset value: 0x0000 0000

         

Bit 11

TERR1

: 

Transmission error of mailbox1

This bit is set when the previous TX failed due to an error. 

Bit 10

ALST1

:

 Arbitration lost for mailbox1

This bit is set when the previous TX failed due to an arbitration lost. 

Bit 9

TXOK1

: 

Transmission OK of mailbox1

The hardware updates this bit after each transmission attempt.
0: The previous transmission failed
1: The previous transmission was successful
This bit is set by hardware when the transmission request on mailbox 1 has been completed 
successfully. Refer to 

Figure 383

Bit 8

RQCP1

: 

Request completed mailbox1

Set by hardware when the last request (transmit or abort) has been performed.
Cleared by software writing a “1” or by hardware on transmission request (TXRQ1 set in 
CAN_TI1R register).
Clearing this bit clears all the status bits (TXOK1, ALST1 and TERR1) for Mailbox 1.

Bit 7

ABRQ0

: 

Abort request for mailbox0

Set by software to abort the transmission request for the corresponding mailbox. 
Cleared by hardware when the mailbox becomes empty.
Setting this bit has no effect when the mailbox is not pending for transmission.

Bits 6:4 Reserved, must be kept at reset value.

Bit 3

TERR0

: 

Transmission error of mailbox0

This bit is set when the previous TX failed due to an error. 

Bit 2

ALST0

: 

Arbitration lost for mailbox0

This bit is set when the previous TX failed due to an arbitration lost.

Bit 1

TXOK0

: 

Transmission OK of mailbox0

The hardware updates this bit after each transmission attempt.
0: The previous transmission failed
1: The previous transmission was successful
This bit is set by hardware when the transmission request on mailbox 1 has been completed 
successfully. Refer to 

Figure 383

Bit 0

RQCP0

: 

Request completed mailbox0

Set by hardware when the last request (transmit or abort) has been performed.
Cleared by software writing a “1” or by hardware on transmission request (TXRQ0 set in 
CAN_TI0R register).
Clearing this bit clears all the status bits (TXOK0, ALST0 and TERR0) for Mailbox 0.

         

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

RFOM0 FOVR0 FULL0

Res.

FMP0[1:0]

rs

rc_w1

rc_w1

r

r

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

B2 ABB2050 Instruction Manual preview
ABB2050
Brand: B2 Pages: 52
Garland EdgeLens INT10G8LR56 User Manual preview
EdgeLens INT10G8LR56
Brand: Garland Pages: 30
CAP-XX Purpose User Manual preview
Purpose
Brand: CAP-XX Pages: 8
Aqua Computer Aquaduct 360 XT Operating And Assembly Manual preview
Aquaduct 360 XT
Brand: Aqua Computer Pages: 28
ENERMAX ELC-LTTR240-TBP User Manual preview
ELC-LTTR240-TBP
Brand: ENERMAX Pages: 16
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
Marani LPP-440A User Manual preview
LPP-440A
Brand: Marani Pages: 39
Laser UDC CARD User Manual preview
UDC CARD
Brand: Laser Pages: 4
IEI Technology WAFER-ULT4 User Manual preview
WAFER-ULT4
Brand: IEI Technology Pages: 136
Variscite VAR-EXT-CB103 Manual preview
VAR-EXT-CB103
Brand: Variscite Pages: 17
Aviosys 9255W User Manual preview
9255W
Brand: Aviosys Pages: 77
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2
Cutting Edge Unity AM Manual preview
Unity AM
Brand: Cutting Edge Pages: 92
IBM TSO/E REXX User Manual preview
TSO/E REXX
Brand: IBM Pages: 242
Intel Core 2 Duo E4300 Design Manual preview
Core 2 Duo E4300
Brand: Intel Pages: 55
National Instruments NI 653x User Manual preview
NI 653x
Brand: National Instruments Pages: 147
Ezviz Vault Plus Quick Start Manual preview
Vault Plus
Brand: Ezviz Pages: 38
ST STEVAL-IHT003V1 User Manual preview
STEVAL-IHT003V1
Brand: ST Pages: 20

Brands by name

Popular brands

Load more brands