manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

302/1080

RM0365

Analog-to-digital converters (ADC)

392

Constraints on the sampling time for fast and slow channels

For each channel, SMP[2:0] bits must be programmed to respect a minimum sampling time 
as specified in the ADC charateristics section of the datasheets.

15.3.13  Single conversion mode (CONT=0)

In Single conversion mode, the ADC performs once all the conversions of the channels. 
This mode is started with the CONT bit at 0 by either:

•

Setting the ADSTART bit in the ADCx_CR register (for a regular channel)

•

Setting the JADSTART bit in the ADCx_CR register (for an injected channel)

•

External hardware trigger event (for a regular or injected channel)

Inside the regular sequence, after each conversion is complete:

•

The converted data are stored into the 16-bit ADCx_DR register

•

The EOC (end of regular conversion) flag is set

•

An interrupt is generated if the EOCIE bit is set

Inside the injected sequence, after each conversion is complete:

•

The converted data are stored into one of the four 16-bit ADCx_JDRy registers

•

The JEOC (end of injected conversion) flag is set

•

An interrupt is generated if the JEOCIE bit is set

After the regular sequence is complete:

•

The EOS (end of regular sequence) flag is set

•

An interrupt is generated if the EOSIE bit is set

After the injected sequence is complete:

•

The JEOS (end of injected sequence) flag is set

•

An interrupt is generated if the JEOSIE bit is set

Then the ADC stops until a new external regular or injected trigger occurs or until bit 
ADSTART or JADSTART is set again.

Note:

To convert a single channel, program a sequence with a length of 1.

15.3.14  Continuous conversion mode (CONT=1)

This mode applies to regular channels only.

In continuous conversion mode, when a software or hardware regular trigger event occurs, 
the ADC performs once all the regular conversions of the channels and then automatically 
re-starts and continuously converts each conversions of the sequence. This mode is started 
with the CONT bit at 1 either by external trigger or by setting the ADSTART bit in the 
ADCx_CR register.

Inside the regular sequence, after each conversion is complete:

•

The converted data are stored into the 16-bit ADCx_DR register

•

The EOC (end of conversion) flag is set

•

An interrupt is generated if the EOCIE bit is set

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

e-Line Technology Network Video Recorders User Manual preview
Network Video Recorders
Brand: e-Line Technology Pages: 34
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Brand: Lattice Semiconductor Pages: 15
Qualys GUARD Quick Start Manual preview
GUARD
Brand: Qualys Pages: 2
Mylex eXtremeRAID 1100 Installation Manual preview
eXtremeRAID 1100
Brand: Mylex Pages: 74
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
Barco Encore VPx Installation Manual preview
Encore VPx
Brand: Barco Pages: 30
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Brand: Danville Signal Processing Pages: 35
axing EOC 1-31 Operation Instructions Manual preview
EOC 1-31
Brand: axing Pages: 52
NC-link NC-AP111 User Manual preview
NC-AP111
Brand: NC-link Pages: 20
NAMCO SOUL CALIBUR II Manual preview
SOUL CALIBUR II
Brand: NAMCO Pages: 26
Doremi MB-4K User Manual preview
MB-4K
Brand: Doremi Pages: 15
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Brand: Paradyne Pages: 108
National Semiconductor Data Capture Board CLC-CAPT-PCASM User Manual preview
Data Capture Board CLC-CAPT-PCASM
Brand: National Semiconductor Pages: 15
Intel G6950 Documentation Update preview
G6950
Brand: Intel Pages: 51
Wistron NeWeb DNBA-81 User Manual preview
DNBA-81
Brand: Wistron NeWeb Pages: 32
IceManCooler ICE-SKY-E User Manual preview
ICE-SKY-E
Brand: IceManCooler Pages: 2
Jabra A330 Multiuse Technical Specifications preview
A330 Multiuse
Brand: Jabra Pages: 2

Brands by name

Popular brands

Load more brands