manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Flexible static memory controller (FSMC)

RM0365

233/1080

DocID025202 Rev 7

consecutive write operations to the address section are required to specify the full 
address.

•

To read or write data,

 the software reads or writes the data from/to any memory 

location in the data section.

Since the NAND Flash memory automatically increments addresses, there is no need to 
increment the address of the data section to access consecutive memory locations.

14.5 

NOR Flash/PSRAM controller

The FMC generates the appropriate signal timings to drive the following types of memories:

•

Asynchronous SRAM and ROM
–

8  bits

–

16 bits

•

PSRAM (Cellular RAM)
–

Asynchronous mode

–

Burst mode for synchronous accesses

–

Multiplexed or non-multiplexed

•

NOR Flash memory
–

Asynchronous mode 

–

Burst mode for synchronous accesses

–

Multiplexed or non-multiplexed

The FMC outputs a unique Chip Select signal, NE[4:1], per bank. All the other signals 
(addresses, data and control) are shared.

The FMC supports a wide range of devices through a programmable timings among which:

•

Programmable wait states (up to 15)

•

Programmable bus turnaround cycles (up to 15)

•

Programmable output enable and write enable delays (up to 15)

•

Independent read and write timings and protocol to support the widest variety of 
memories and timings

•

Programmable continuous clock (FMC_CLK) output.

The FMC Clock (FMC_CLK) is a submultiple of the HCLK clock. It can be delivered to the 
selected external device either during synchronous accesses only or during asynchronous 
and synchronous accesses depending on the CCKEN bit configuration in the FMC_BCR1 
register:

•

If the CCLKEN bit is reset, the FMC generates the clock (CLK) only during 
synchronous accesses (Read/write transactions). 

•

If the CCLKEN bit is set, the FMC generates a continuous clock during asynchronous 
and synchronous accesses. To generate the FMC_CLK continuous clock, Bank 1 must 
be configured in synchronous mode (see 

Section 14.5.6: NOR/PSRAM controller 

registers

). Since the same clock is used for all synchronous memories, when a 

continuous output clock is generated and synchronous accesses are performed, the 
AHB data size has to be the same as the memory data width (MWID) otherwise the 
FMC_CLK frequency will be changed depending on AHB data transaction (refer to 

Section 14.5.5: Synchronous transactions

 for FMC_CLK divider ratio formula). 

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
TC-Helicon PERFORM-VK Quick Start Manual preview
PERFORM-VK
Brand: TC-Helicon Pages: 2
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
Dahua Smart 1U Quick Start Manual preview
Smart 1U
Brand: Dahua Pages: 24
3Com Token Ring Getting Started Manual preview
Token Ring
Brand: 3Com Pages: 18
Supermicro SC836 X9 User Manual preview
SC836 X9
Brand: Supermicro Pages: 24
SAB SABVISION NVR32 Quick Start Manual preview
SABVISION NVR32
Brand: SAB Pages: 29
WABCO CAN Router Manual preview
CAN Router
Brand: WABCO Pages: 29
Element14 Wireless Connectivity Cape Quick Start Manual preview
Wireless Connectivity Cape
Brand: Element14 Pages: 2
Aaeon SBC-555 Manual preview
SBC-555
Brand: Aaeon Pages: 72
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Brand: Magewell Pages: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Brand: Z3 Technology Pages: 18
Keithley 7075 Instruction Manual preview
7075
Brand: Keithley Pages: 108
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Brand: Microcomputer Systems Pages: 21

Brands by name

Popular brands

Load more brands