manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

666/1080

RM0365

General-purpose timers (TIM15/TIM16/TIM17)

692

Bit 5

CC2P

: Capture/Compare 2 output polarity

Refer to CC1P description

Bit 4

CC2E

: Capture/Compare 2 output enable

Refer to CC1E description

Bit 3

CC1NP

: Capture/Compare 1 complementary output polarity

CC1 channel configured as output:

0: OC1N active high
1: OC1N active low

CC1 channel configured as input:

This bit is used in conjunction with CC1P to define the polarity of TI1FP1 and TI2FP1. Refer
to CC1P description.

Note: 1.This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK 

bits in TIMx_BDTR register) and CC1S=”00” (the channel is configured in output).
2. On channels that have a complementary output, this bit is preloaded. If the CCPC bit 
is set in the TIMx_CR2 register then the CC1NP active bit takes the new value from the 
preloaded bit only when a Commutation event is generated.

Bit 2

CC1NE

: Capture/Compare 1 complementary output enable

0: Off - OC1N is not active. OC1N level is then function of MOE, OSSI, OSSR, OIS1, OIS1N 
and CC1E bits.
1: On - OC1N signal is output on the corresponding output pin depending on MOE, OSSI, 
OSSR, OIS1, OIS1N and CC1E bits.

Bit 1

CC1P

: Capture/Compare 1 output polarity

CC1 channel configured as output:

0: OC1 active high
1: OC1 active low

CC1 channel configured as input: 

The CC1NP/CC1P bits select the polarity of TI1FP1 and 

TI2FP1 for trigger or capture operations.

00: non-inverted/rising edge. The circuit is sensitive to TIxFP1 rising edge (capture or trigger 
operations in reset, external clock or trigger mode), TIxFP1 is not inverted (trigger operation 
in gated mode).
01: inverted/falling edge. The circuit is sensitive to TIxFP1 falling edge (capture or trigger 
operations in reset, external clock or trigger mode), TIxFP1 is inverted (trigger operation in 
gated mode).
10: reserved, do not use this configuration.
11: non-inverted/both edges. The circuit is sensitive to both TIxFP1 rising and falling edges 
(capture or trigger operations in reset, external clock or trigger mode), TIxFP1 is not inverted 
(trigger operation in gated mode). 

Note: 1. This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK 

bits in TIMx_BDTR register).
2. On channels that have a complementary output, this bit is preloaded. If the CCPC bit 
is set in the TIMx_CR2 register then the CC1P active bit takes the new value from the 
preloaded bit only when a Commutation event is generated.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
ebm-papst 4112 N/2HU Operating Manual preview
4112 N/2HU
Brand: ebm-papst Pages: 6
ebm-papst 4314 N/2HHPU Operating Manual preview
4314 N/2HHPU
Brand: ebm-papst Pages: 6
ebm-papst 8312 L Operating Manual preview
8312 L
Brand: ebm-papst Pages: 5
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
Paradyne Fan Tray 8820-S2-900 Installation Instructions Manual preview
Fan Tray 8820-S2-900
Brand: Paradyne Pages: 6
Xmart SNMP06 Reference Manual preview
SNMP06
Brand: Xmart Pages: 8
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Brand: red lion Pages: 5
FDI ELI70-CR Quick Start Manual preview
ELI70-CR
Brand: FDI Pages: 2
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
Longshine LCS-8170 User Manual preview
LCS-8170
Brand: Longshine Pages: 35
AC&NC JetStor NAS 724UX User Manual preview
JetStor NAS 724UX
Brand: AC&NC Pages: 117
Avenview DVI-PROWALL-9X Instruction Manual preview
DVI-PROWALL-9X
Brand: Avenview Pages: 28
AXIOMTEK CEM500 Quick Installation Manual preview
CEM500
Brand: AXIOMTEK Pages: 2
Delta Electronics PFC Chokes PFC3515V Series Specification Sheet preview
PFC Chokes PFC3515V Series
Brand: Delta Electronics Pages: 1
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35

Brands by name

Popular brands

Load more brands