manualshive.com logo in svg

Omron OMNUC W Series, User Manual

The Omron OMNUC W Series User Manual is essential for maximizing the potential of your product. This comprehensive manual provides step-by-step instructions and detailed explanations, ensuring a seamless user experience. Download it for free from manualshive.com to unlock the full functionality of your OMNUC W Series product.

Share
Download
background image

5-12

Display

Countermeasures

Cause of error

Status when error

occurs

Error

Overspeed

Occurs when the

servo is ON.

Encoder signal be-

tween controllers is

wired incorrectly.

Rewire correctly.

Servomotor power

line is wired incor-

rectly.

Rewire correctly.

Occurs along with

high-speed rotation

when a command is

Position and speed

command inputs are

too large.

Input command values

correctly.

input.

Pn300 (speed com-

mand scale), and

Pn202 and Pn203

(electronic gear) set-

tings are too large.

Set the parameters cor-

rectly.

Speed limit is not

performed during

torque control.

Set Pn407 (speed limit)

Rotation limit has

been exceeded due

to overshooting.

Adjust the gain.
Lower the maximum spe-

cified speed.

Overload

Occurs during op-

eration.

Running at over

245% of rated

torque (effective

torque).

Repair the Servomotor

shaft if it is locked.
If the Servomotor power

line is wired incorrectly,

rewire it correctly.
Lighten the load.
Lengthen the accelera-

tion and deceleration

times.
Adjust the gain.

Power supply volt-

age has fallen.

Check the power supply

voltage, and lower to

within tolerance range.

Overload

Occurs during op-

eration.

Running at 120% to

245% of rated

torque (effective

torque).

Lighten the load.
Lengthen the accelera-

tion and deceleration

times.
Adjust the gain.

Power supply volt-

age has fallen.

Check the power supply

voltage, and lower to

within tolerance range.

Dynamic brake

overload

Occurs when the

servo is turned OFF

after operating.

Energy required for

stopping exceeds

the dynamic brake

resistor tolerance.

Lower the rotation speed.
Reduce the load inertia.
Reduce the frequency of

dynamic brake use.

Occurs when the

power supply is

turned ON.

Control panel error

Replace the Servo Driver.

Troubleshooting

Chapter 5

AUDIN - 7 bis rue de Tinqueux - 51100 Reims - France - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]

Summary of Contents for OMNUC W Series

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMNUC W Series

Fastech Ezi-SERVO ST Operation Manual preview
Ezi-SERVO ST
Brand: Fastech Pages: 40
York MILLENIUM 351-46 Operating Instructions Manual preview
MILLENIUM 351-46
Brand: York Pages: 24
TECO JSDE Series Manual preview
JSDE Series
Brand: TECO Pages: 62
YASKAWA SGDV-OFB03A Product Manual preview
SGDV-OFB03A
Brand: YASKAWA Pages: 114
Emerson Dixell XEV23D Installing And Operating Instructions preview
Dixell XEV23D
Brand: Emerson Pages: 4
Emerson IC866-ICH-006-603-20 Installation Manual preview
IC866-ICH-006-603-20
Brand: Emerson Pages: 10
Emerson unidrive m300 Quick Start Manual preview
unidrive m300
Brand: Emerson Pages: 36
Emerson EV3 Series Application Manuallines preview
EV3 Series
Brand: Emerson Pages: 34
Emerson EVH Series Installation Manual preview
EVH Series
Brand: Emerson Pages: 52
Emerson Copeland EVM Series Installation Manual preview
Copeland EVM Series
Brand: Emerson Pages: 31
Emerson Control Techniques Focus 3N User Manual preview
Control Techniques Focus 3N
Brand: Emerson Pages: 82
Emerson EV2000 Series User Manual preview
EV2000 Series
Brand: Emerson Pages: 131
Emerson Unidrive M400 User Manual preview
Unidrive M400
Brand: Emerson Pages: 198
Emerson Control Techniques Epsilon Eb-202 Installation Manual preview
Control Techniques Epsilon Eb-202
Brand: Emerson Pages: 134
Emerson Mentor MP Advanced User'S Manual preview
Mentor MP
Brand: Emerson Pages: 222
Emerson MP105A4 User Manual preview
MP105A4
Brand: Emerson Pages: 182
Emerson Unidrive M702 User Manual preview
Unidrive M702
Brand: Emerson Pages: 284
Emerson Copeland EVH Series Quick Start Manual preview
Copeland EVH Series
Brand: Emerson Pages: 2

Brands by name

Popular brands

Load more brands