mori seiki ZL-153 Operation Manual Download Page 339

Page: 339 / 561

CHUCKING C-1

CAUTIONS ON CHUCKING A WORKPIECE

When chucking a workpiece, pay attention to the following points.

DANGER

Always switch the power OFF before mounting, removing, inspecting, or

lubricating the chuck. If you carry out maintenance and inspection work

with the power left ON, you could be entangled with the spindle and

seriously injured if the spindle starts for some reason.

For details on chuck maintenance, refer to the instruction manuals

prepared by the chuck and cylinder manufacturers.

WARNING

When mounting a chuck, chuck cylinder, or connection rod to the

spindle, read the instruction manuals provided by Mori Seiki, the

chuck manufacturer, and the chuck cylinder manufacturer. The

considerations that must be attended to are given in the instruction

manuals. If the chuck, chuck cylinder, or connection rod is mounted

to the spindle without understanding these considerations, the

chuck, chuck cylinder or connecting rod will be damaged, and if

machining is carried out after such damage has occurred, a

workpiece, the chuck, and/or chuck jaw could fly out, causing

accidents involving serious injuries or damage to the machine.

If a workpiece holding fixture other than the chuck supplied with the

machine is used, be sure to contact Mori Seiki to prevent accidents.

Mori Seiki is not responsible for accidents caused by the use of a

fixture prepared by the customer without consulting Mori Seiki.

If the chuck supplied with the machine is removed from the machine

and a specially prepared fixture is used instead of the chuck to hold

a workpiece, remove the chuck cylinder and the connecting rod if

they do not operate due to the mounting of the special fixture. If the

spindle is started with the chuck cylinder and the connecting rod still

mounted, the connecting rod will vibrate and the connecting rod and

the chuck cylinder could become detached, causing accidents

involving serious injuries or damage to the machine.

Leave the pilot bush mounted in the chuck.

If the machine is operated with the pilot bush removed, a master jaw

or a jaw of the chuck could fly out, causing accidents involving

serious injuries or damage to the machine.

The socket hole in the hexagon socket head cap bolts used for

mounting chuck jaws and fixtures will become enlarged over a long

period of use. Check these hexagon socket head cap bolts at

regular intervals and if a hexagon wrench does not fit in the socket

hole, replace the bolt with new one.

If there is an excessive gap between the socket hole and hexagon

wrench, the bolt cannot be torqued correctly. If the machine is

operated while a bolt is not torqued correctly, a workpiece, chuck

jaw or a fixture could fly out, causing accidents involving serious

injuries or damage to the machine.

Summary of Contents for ZL-153


















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZL-153

Reviews:

Related manuals for ZL-153

Brands by name

Popular brands

mori seiki ZL-153, Operation Manual

Search results

Summary of Contents for ZL-153

Reviews:

Related manuals for ZL-153

Brands by name

Popular brands