Mitsubishi Electric FR-A820-00046 (0.4K), Instruction Manual

Page: 532 / 1218

(H) Protective function parameter Parameters
5 - 330
Setting multiple stall prevention operation levels (Pr. 48, Pr. 49, Pr. 114, Pr. 115)
●
By setting Pr. 49 "Second stall prevention operation frequency" = "9999" and turning ON the RT
signal, Pr. 48 "Second stall prevention operation level" will be enabled.
●
For Pr. 48 (Pr. 114), set the stall prevention operation level that is effective in the output frequency
range between 0 Hz and Pr. 49 (Pr. 115). However, the operation level is Pr. 22 during acceleration.
●
Stop-on-contact operation can be used by decreasing the Pr. 48 (Pr. 114) setting and loosening
the reduction torque (torque when stopped).
●
Pr. 114 and Pr. 115 are enabled when the X9 signal is ON. To input the X9 signal, set "9" in any of
Pr. 178 to Pr. 189 (input terminal function selection) to assign the function to the terminal.
For the stall prevention operation level, the smaller of Pr. 22 and Pr. 48 (Pr. 115) has precedence.
When Pr. 858 = "4 (analog input to terminal 4 for stall prevention operation level)" or Pr. 868 = "4
(analog input to terminal 1 for stall prevention operation level)", turning ON the RT (X9) signal will
not enable the second (third) stall prevention function. (Input to the terminal 4 or terminal 1 is
valid.)
Pr. 49 setting Pr. 115 setting Operation
0 (initial value) The second (third) stall prevention function disabled.
0.01 Hz to 590 Hz
The second (third) stall prevention function operates according to the
frequency.
9999
Setting not available
The second stall prevention function operates according to the RT signal.
RT signal ON: stall level Pr. 48
RT signal OFF: stall level Pr. 22
Tab. 5-124: Settings of parameter 49 and 115
I002599E
Fig. 5-143: Stall prevention operation level setting example
NOTES When Pr. 49 ≠ "9999" (level change according to frequency) and Pr. 48 = "0%", the stall prevention
function will be disabled at or lower than the frequency set in Pr. 49.
The RT signal is assigned to the terminal RT in the initial status. Set "3" in any of Pr. 178 to Pr. 189
(input terminal function selection) to assign the RT signal to another terminal.
Changing the terminal assignment using Pr. 178 to Pr. 189 (input terminal function selection) may
affect the other functions. Set parameters after confirming the function of each terminal.
The RT (X9) signal acts as the second (third) function selection signal and makes the other second
(third) functions valid. (Refer to page 5-445.)
Output
frequency (Hz)
Output
frequency
During acceleration
During deceleration/constant speed
Running frequency
Pr. 49
Pr. 115
Set frequency is Pr. 49 (Pr. 115) or less
Pr. 48 (Pr. 114) used
Time
Stall
prvention
level
Pr. 22 used
Pr. 48
Pr. 114
Stall pr
ev
ention
o
p
era
ti
o
n curr
ent
Pr. 49 (Pr. 115)
Set frequency
Output
frequency (Hz)
Output
frequency
Time
Stall
prvention
level
Set frequency exceeds Pr. 49 (Pr. 115)
Pr. 48 (Pr. 114) used
Pr. 22 used
Set frequency
Pr. 49 (Pr. 115)