Mitsubishi Electric FR-A820-00046 (0.4K), Instruction Manual

Page: 582 / 1218

(M) Monitor display and monitor output signal Parameters
5 - 380
26 126 FIN
Heatsink overheat pre-
alarm
Output when the heatsink temperature
reaches about 85% of the heatsink
overheat protection operation
temperature.
⎯
6-23
27 127 ORA
Orientation complete
(for vector control
compatible option)
When orientation is enabled.
Pr. 350 to
Pr. 366, Pr. 369,
Pr. 393, Pr. 396
to Pr. 399
5-522
28 128 ORM
Orientation fault
(for vector control
compatible option)
30 130 Y30
Forward rotation output
(for vector control
compatible option)
Output during motor forward rotation.
⎯
5-387
31 131 Y31
Reverse rotation output
(for vector control
compatible option)
Output during motor reverse rotation. 5-387
32 132 Y32
Regenerative status
output
(for vector control
compatible option)
Output when the regenerative status is
entered under vector control.
5-388
33 133 RY2 Operation ready 2
Output during pre-excitation or
operation under Real sensorless vector
control, vector control, and PM sensorless
vector control.
⎯
5-384
34 134 LS Low speed detection
Output when the output frequency
drops to the Pr. 865 setting or lower.
Pr. 865 5-390
35 135 TU Torque detection
Output when the motor torque is higher
than the Pr. 864 setting.
Pr. 864 5-396
36 136 Y36 In-position
Output when the number of droop
pulses drops below the setting.
Pr. 426 5-187
38 138 MEND Travel completed
Output when the droop pulse is within
the in-position width, and the position
command operation is not completed or
performing home position return.
Pr. 426 5-187
39 139 Y39
Start time tuning
completion Output when tuning is completed during
start-up.
Pr. 95, Pr. 574 5-482
40 140 Y40 Trace status Output during trace operation.
Pr. 1020 to
Pr. 1047
5-610
41 141 FB Speed detection
Output when the actual motor rotations
per minute (estimated rotations per
minute) reaches Pr. 42 (Pr. 50, Pr. 116).
Pr. 42, Pr. 50,
Pr. 116
5-390 42 142 FB2 Second speed detection
43 143 FB3 Third speed detection
44 144 RUN2 Inverter running 2
Output while the forward rotation or
reverse rotation signal is ON.
Output during deceleration even while
the forward rotation or reverse rotation
signal is OFF. (Not output while pre-
excitation LX is ON.)
Output also while the orientation
command (X22) signal is ON.
Under position control, turns ON when
the servo is turned ON (LX ON). (Turns
OFF when the servo turned is OFF (LX
OFF)).
⎯
5-384
45 145 RUN3
Inverter running and start
command is ON Output while the inverter is running and
the start command is ON.
⎯
5-384
46 146 Y46
During deceleration at
occurrence of power
failure Output after the power-failure
deceleration function operates.
(Retained until canceled.)
Pr. 261 to
Pr. 266
5-599
47 147 PID
During PID control
activated
Output during PID control.
Pr. 127 to
Pr. 134, Pr. 575
to Pr. 577
5-543
48 148 Y48 PID deviation limit
Output when the absolute deviation
value exceeds the limit value.
Pr. 127 to
Pr. 134, Pr. 553,
Pr. 554
5-543
Setting
Signal
name
Function Operation
Related
parameter Refer to
page
Positive
logic
Negative
logic
Tab. 5-144: Output terminal function assignment (2)