Mitsubishi Electric FR-A820-00046 (0.4K), Instruction Manual

Page: 248 / 1218

Parameter List Parameters
5 - 46
(A) Application parameters
Parameters to set a specific application.
Pr.
group
Pr. Name
Refer to
page
A000 135
Electronic bypass sequence
selection
5-488
A001 136 MC switchover interlock time 5-488
A002 137 Start waiting time 5-488
A003 138 Bypass selection at a fault 5-488
A004 139
Automatic switchover frequency
from inverter to bypass operation
5-488
A005 159
Automatic switchover frequency
range from bypass to inverter
operation
5-488
A006 248 Self power management selection 5-497
A007 254 Main circuit power OFF waiting time 5-497
A100 278 Brake opening frequency 5-501
A101 279 Brake opening current 5-501
A102 280
Brake opening current detection
time
5-501
A103 281 Brake operation time at start 5-501
A104 282 Brake operation frequency 5-501
A105 283 Brake operation time at stop 5-501
A106 284
Deceleration detection function
selection
5-501
A107 285 Overspeed detection frequency
5-124,
5-501
A108 639 Brake opening current selection 5-501
A109 640 Brake operation frequency selection 5-501
A110 292 Automatic acceleration/deceleration
5-263,
5-268,
5-501
A120 642 Second brake opening frequency 5-501
A121 643 Second brake opening current 5-501
A122 644
Second brake opening current
detection time
5-501
A123 645 Second brake operation time at start 5-501
A124 646 Second brake operation frequency 5-501
A125 647 Second brake operation time at stop 5-501
A126 648
Second deceleration detection
function selection
5-501
A128 650
Second brake opening current
selection
5-501
A129 651
Second brake operation frequency
selection
5-501
A130 641
Second brake sequence operation
selection
5-501
A170 1410 Starting times lower 4 digits 5-507
A171 1411 Starting times upper 4 digits 5-507
A200 270
Stop-on contact/load torque high-
speed frequency control selection 5-509,
5-513
A201 271
High-speed setting maximum
current
5-513
A202 272
Middle-speed setting minimum
current
5-513
Tab. 5-13: Application parameters (1)
A203 273 Current averaging range 5-513
A204 274
Current averaging filter time
constant
5-513
A205 275
Stop-on contact excitation current
low-speed multiplying factor
5-509
A206 276
PWM carrier frequency at stop-on
contact
5-509
A300 592 Traverse function selection 5-517
A301 593 Maximum amplitude amount 5-517
A302 594
Amplitude compensation amount
during deceleration
5-517
A303 595
Amplitude compensation amount
during acceleration
5-517
A304 596 Amplitude acceleration time 5-517
A305 597 Amplitude deceleration time 5-517
A310 1072
DC brake judgment time for anti-
sway control operation
5-519
A311 1073
Anti-sway control operation
selection
5-519
A312 1074 Anti-sway control frequency 5-519
A313 1075 Anti-sway control depth 5-519
A314 1076 Anti-sway control width 5-519
A315 1077 Rope length 5-519
A316 1078 Trolley weight 5-519
A317 1079 Load weight 5-519
A510
350
Stop position command selection 5-522
A511
360
16-bit data selection 5-522
A512 361 Position shift 5-522
A520
362
Orientation position loop gain 5-522
A521
363
Completion signal output delay time 5-522
A522
364
Encoder stop check time 5-522
A523
365
Orientation limit 5-522
A524 366 Recheck time 5-522
A525
393
Orientation selection 5-522
A526
351
Orientation speed 5-522
A527
352
Creep speed 5-522
A528
353
Creep switchover position 5-522
A529 354 Position loop switchover position 5-522
A530
355
DC injection brake start position 5-522
A531
356
Internal stop position command 5-522
A532
357
Orientation in-position zone 5-522
A540
394
Number of machine side gear teeth 5-522
A541 395 Number of motor side gear teeth 5-522
A533
358
Servo torque selection 5-522
A542
396
Orientation speed gain (P term) 5-522
A543
397
Orientation speed integral time 5-522
A544
398
Orientation speed gain (D term) 5-522
A545 399 Orientation deceleration ratio 5-522
Pr.
group
Pr. Name
Refer to
page
Tab. 5-13: Application parameters (2)