HP Storageworks 8100 - enterprise virtual array User Manual Download Page 358 | Manualshive

Page: 358 / 408

background image

Korean notices

Safety

Battery replacement notice

Your switch is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline
internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery
is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider
using the HP spare part designated for this product. For more information about battery replacement
or proper disposal, contact an HP authorized service provider.

WARNING!

Your switch contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline
battery pack. There is risk of fire and burns if the battery pack is not properly handled. To reduce the
risk of personal injury:

•

Do not attempt to recharge the battery.

•

Do not expose to temperatures higher than 60° C.

•

Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.

•

Replace only with the HP spare part designated for this product.

Regulatory compliance and safety

358

«
...
356
357
358
359
360
...
»

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Storageworks 8100 - enterprise virtual array

Brand: cable matters Pages: 13

Brand: J5create Pages: 2

Brand: P.I. Engineering Pages: 4

Brand: PATONA Pages: 14

Brand: Intermec Pages: 2

Brand: ZLAN Pages: 18

Brand: Renesas Pages: 2

Brand: MSI Pages: 41

Brand: MSI Pages: 74

Brand: GE Pages: 8

Digital Energy 1018959

Brand: GE Pages: 24

Brand: GE Pages: 2

Brand: GE Pages: 15

Brand: GE Pages: 24

Digital Energy 1018959

Brand: GE Pages: 69

Masoneilan VECTOR V1100

Brand: GE Pages: 60

Brand: GE Pages: 2

Brand: Goobay Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands