HP Storageworks 8100 - enterprise virtual array User Manual Download Page 145

Page: 145 / 408

Table 25 Migration rates for single configuration

Two Ports per Array Control-
ler Connected to Each Fabric

One Port per Array Control-
ler Connected to Each Fab-

ric

Fibre Channel fab-

ric

Source or destination array

2.5 TB/hour

1.25 TB/hour

4 Gb

2 Gb Fibre Channel

4 TB/hour

2.5 TB/hour

8 Gb

4 Gb Fibre Channel

4 TB/hour

8 Gb

8 Gb Fibre Channel

Figure 88

shows the configuration used when you are:

•

Migrating from one vendor SAN to another vendor SAN.

•

Installing a new fabric and do not have enough ports available in the new fabric.

Figure 88 Migration between dissimilar vendor SANs

Supported Fibre Channel fabrics

DMS is currently supported with B-series and C-series 2Gb, 4Gb, and 8Gb Fibre Channel fabrics.

Supported storage arrays

Table 26

lists the storage array types for which DMS currently provides support.

Table 26 Supported storage arrays

Storage array

Vendor

CLARiiON CX family
CLARiiON AX family

EMC

Attachable Modular Storage (AMS) family
Workgroup Modular Storage (WMS) family

Hitachi Data Systems (HDS)

HP StorageWorks Modular Storage Array (MSA) family
HP StorageWorks Enterprise Virtual Array (EVA) family

Hewlett-Packard (HP)

System Storage DS4000 family
System Storage DS5000 family

IBM

MPX200 Multifunction Router

145

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands

HP Storageworks 8100 - enterprise virtual array, User Manual

Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands