HP Storageworks 8100 - enterprise virtual array User Manual Download Page 305

Page: 305 / 408

MPX200 <1>(admin) #>

target rm

Index State (WWNN,WWPN/iSCSI Name)

----- ----- ----------------------

0 Offline 20:00:00:14:c3:3d:d2:bf,22:00:00:14:c3:3d:d2:bf

1 Online 20:00:00:14:c3:44:9b:86,22:00:00:14:c3:44:9b:86

2 Online 20:00:00:14:c3:44:9b:9d,22:00:00:14:c3:44:9b:9d

3 Online 20:00:00:14:c3:44:9a:fa,22:00:00:14:c3:44:9a:fa

Please select an OFFLINE Target from the list above ('q' to

quit): 0

All attribute values for that have been changed will now be

saved.

Traceroute

Displays the route that a network packet takes to reach the specified destination.

Admin session

Authority

traceroute

Syntax

Example:

MPX200 <1>(admin) #>

traceroute

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

IP Address (IPv4 or IPv6) [0.0.0.0]

172.35.14.17

Outbound Port (0=Mgmt, 1=GE1, 2=GE2, ...) [Mgmt ]

Tracing route to 172.35.14.17 over a maximum of 30 hops:

1 172.17.136.2 0.4ms 0.3ms 0.5ms

2 10.7.9.5 1.1ms 1.1ms 1.1ms

3 172.21.130.233 2.7ms 2.7ms 2.6ms

4 172.21.4.245 291.4ms 291.4ms 291.4ms

5 172.21.4.246 413.6ms 417.1ms 439.2ms

6 10.35.9.1 459.1ms 465.6ms 480.0ms

7 172.35.14.17 495.3ms 483.0ms 505.9ms

Traceroute completed in 7 hops.

MPX200 Multifunction Router

305

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands

HP Storageworks 8100 - enterprise virtual array, User Manual

Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands